Philips 47PDL6907H Specifications download pdf (Page 7)

If your router has WPS, you can directly connect to the router

without scanning. Go to the router, press the WPS button and

return to the TV within 2 minutes. Then press Connect to

make the connection.

If you have devices in your wireless network that use the WEP

security encryption system, you cannot use WPS.

If you must use the WPS pin code to connect, select Scan

instead of WPS.

Step 6 - In the list of networks found, select your wireless

network and press OK.

If your network is not in the list because the network name is

hidden (you switched off the SSID broadcast of the router),

select Manual entry to enter the network name yourself.

Step 7 - Depending on the type of router, you can now enter

your encryption key (WEP, WPA or WPA2). If you entered the

encryption key for this network before, you can select Next to

make the connection immediately.

If your router supports WPS or WPS pin, you can select WPS,

WPS pin or Standard. Select your choice and press OK.

- Standard

Select Standard to enter the encryption key (password,

passphrase or security key) manually. You can use the

keyboard on the RC to enter the encryption key. Once you

have entered the key, press Connect.

- WPS pin

To make a secured WPS connection with a PIN code, select

WPS pin and press OK. Write down the 8-digit PIN code

shown and enter it in the router software on your PC. Return

to the TV and press Connect. Consult the router manual on

where to enter the PIN code in the router software.

Step 8 - A message will be shown when the connection is

successful.

Network configuration

If the connection fails, you can check the DHCP setting of the

router. DHCP should be set to On.

Alternatively, if you are an advanced user and want to install

your network with static IP addressing, set the TV to Static IP.

To set the TV to Static IP, press h and select S Setup and

press OK. Select Network settings > Network configuration

> Static IP. With Static IP selected in the menu, you can set

the IP address and other necessary settings in Static IP

configuration in the same menu.

Network problems

Wireless network not found or distorted

• Microwave ovens, DECT phones or other Wi-Fi 802.11b/g/n

devices in your proximity might disturb the wireless network.

• Make sure that the firewalls in your network allow access to

the TV's wireless connection.

• If the wireless network does not work properly in your home,

try the wired network installation.

Internet does not work

• If the connection to the router is OK, check the router

connection to the Internet.

The PC and Internet connection are slow

• Look in your wireless router's user manual for information on

indoor range, transfer rate and other factors of signal quality.

• Use a high-speed (broadband) Internet connection for your

router.

Wired connection

What you need

You need a network router to connect the TV to the Internet.

Use a router with a high-speed (broadband) connection to the

Internet.

Installation

Follow steps 1 to 5.

1 - Connect the router to the TV with a network cable

(Ethernet cable**).

2 - Make sure that the router is switched on.

3 - Press h and select S Setup and press OK.

4 - Select Connect to network and press OK.

5 - Select Wired and press OK.

The TV constantly searches for the network connection. A

message will be shown when the connection is successful.

Network configuration

If the connection fails, you can check the DHCP setting of the

router. DHCP should be set to On.

Alternatively, if you are an advanced user and want to install

your network with static IP addressing, set the TV to Static IP.

To set the TV to Static IP, press h and select S Setup and

press OK.

Select Network settings > Network configuration > Static

IP. With Static IP selected in the menu, you can set the IP

address and other necessary settings in Static IP configuration

in the same menu.

DLNA

The TV uses the DLNA protocol to find and open files on

other devices in your network, like your computer. You can

use a computer with a Microsoft Windows XP, Vista or

Windows 7, Mac OSX or Linux operating system.

Media server software

With media server software on your computer, you can open

your photos, music and videos stored on your computer on

your TV screen.

Use a recent version of media server software like Windows

Media Player 11, Twonky™ or similar*.

Install the software on your computer and set it up to share

your media files with the TV. Read the manual of the media

server software for more information.

To open your files on TV, the media server software must be

running on your computer.

* In Help, press L List and look up Media server software,

supported for an overview of supported media server software.

Setting up / Network 7

1 2 3 4 5 6 7 8 9 10 11 12 ... 57 58

Comments to this Manuals

No comments

Philips 47PDL6907H Specifications Page 7

Comments to this Manuals

Related products and manuals for LED TVs Philips 47PDL6907H