Philips FW-M55 User Manual download pdf (Page 23)

L-/CVJ n (g U /c: UCI I lUI (, ¡1 yuu pi coo

any source (or standby-on) button, the

system will switch to the respective

mode (or standby).

When the system is switched to

standby mode, the demonstration will

resume five seconds later.

removed from and reconnected to the

wall socket the demonstration will

remain off until It Is switched on again.

O

CD / MP3-CD

Disc Change

You can change the outer two discs

while the third inner disc is stopped or

is playing.

1 Press DISC CHANGE

The disc carousel tray slides out.

2 Replace the discs in the left and right

disc trays.

• If you press DISC CHANGE again

during playback, the disc will stop

playing.

The disc carousel tray will rotate

until the inner tray is rotated out

and is ready for changing.

3 Press OPEN'CLOSE to close the

disc carousel tray.

Selecting a desired track

Selecting a desired track when

playback is stopped

• Press digit 0 - 9 on the remote

control to select the desired track.

Playback will start immediately for

the selected track.

The selected track number and

elapsed playing time appear on

the display.

Selecting a desired track during

playback

• Press M or H (or digit 0-9 on the

remote control) until the desired track

appears on the display.

— The selected track number and

elapsed playing time appear on

the display.

• If you press M once it will skip to

the beginning of the previous track

and play the track.

For MP3-CD only

1 Press ALBUM —/+ until the

desired Album appears on the

display.

2 Press TITLE —/ + until the desired

Title appears on the display.

“*■ The selected track number and

elapsed playing time appear on

the display.

3 Press PLAY ►!! to start playback.

Searching for a particular

passage during playback

• Press or ►► until the desired

passage is located.

The volume will be reduced.

• Press PLAY ►!! to resume normal

playback.

P rogram m i n g Tr ac ks

Programming tracks of a loaded disc is

possible when playback is stopped.The

display will indicate the total tracks

stored in the program. Up to 99 tracks

can be stored in the memory in any

order When 99 tracks are stored and

you attempt to store another track, the

display will show‘FULL”.

1 Load the desired discs in the disc

trays.

2 Press the CD (CD 1 *2*3) button to

select the disc tray.

^ Programming can only be done on

the selected disc.

3 Press PROG to start programming.

The PROGRAM starts flashing.

-* It will cancel any previously

programmed tracks and selected

repeat mode.

4 Press M or W (or digit 0-9 on the

remote control) to select the desired

track.

• For MP3-CD, press ALBUM — / +

and TITLE —/+ to select the

desired Album and Title for

programming.

5 Press PROG to store the track.

• Repeat steps 4 to 5 to store other

tracks.

6 Press ■ once to end programming.

The total number of tracks

programmed and total playing

time appear on the display.

Notes:

- ForMP3-CD, total playing time will not

be shown.

- If the total playing time is more than

“NUWhi" then "

........

•

.......

"appears on

the display Instead of the total playing

time.

- If the system is reading the disc,

programming is not possible,

" will be

displayed.

- During programming, if no button is

pressed within 20 seconds, the system

will exit program mode automatically.

Reviewing the program

Reviewing of the program is possible

only when playback is stopped.

1 Press !◄ or ►! repeatedly to review

the programmed tracks.

2 Press ■ once to exit review mode.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 97 98

Comments to this Manuals

No comments