Philips 55PUK7150 User Manual Page 69

  • Download
  • Add to my manuals
  • Print
  • Page
    / 114
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 68
To add a satellite…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation > Search for
satellite and select Add Satellite. The current
satellites are shown.
3 - Select Search. The TV will search for new
satellites.
4 - If the TV has found one or more satellites,
select Install. The TV installs the channels of the
found satellites.
5 - To store the channels and radio stations,
select Finish.
Remove a Satellite
You can remove one or more satellites from your
current satellite installation. You remove the satellite
and its channels. Some satellite operators do not
allow removing a satellite.
To remove satellites…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation > Search for
satellite and select Remove Satellite. The current
satellites are shown.
3 - Select on the satellite(s) to mark or unmark them
to remove.
4 - Select Remove. The satellites are removed.
5 - Select Exit to close Remove Satellite.
Manual Installation
Manual Installation is intended for expert users.
You can use Manual Installation to quickly add new
channels from a satellite transponder. You need to
know the frequency and polarization of the
transponder. The TV will install all channels of that
transponder. If the transponder was installed before,
all its channels - the former and the new ones - are
moved to the end of the channel list All.
You cannot use Manual installation if you need to
change the number of satellites. If this is needed, you
have to do a complete installation with Install
Satellites.
To install a transponder…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation and select Manual
Installation.
3 - If you have more than 1 satellite installed, select
the satellite/LNB for which you want to add channels.
4 - Set the Polarization you need. If you set
the Symbol Rate Mode to Manual, you can enter
the symbol rate in Symbol Rate manually. Enter
the Frequency and start searching for the
transponder.
5 - If a transponder is found, select Store to store
the new transponder on the selected LNB.
6 - Select Exit to leave the manual installation.
LNB Settings
In some countries, you can adjust some expert
settings for each LNB.
LNB Power
By default, LNB Power is set to On.
22 kHz Tone
By default, the Tone is set to Auto.
Low LO Frequency / High LO Frequency
The local oscillator frequencies are set to standard
values. Adjust the values only in case of exceptional
equipment that needs different values.
Problems
The TV cannot find the satellites I want or the TV
installs the same satellite twice
• Make sure that the correct number of satellites is set
in Settings at the start of the installation. You can set
the TV to search for One, Two or 3/4 satellites.
A dual head LNB cannot find a second satellite
• If the TV finds one satellite but cannot find a second
one, turn the dish a few degrees. Align the dish to get
the strongest signal on the first satellite. Check the
signal strength indicator of the first satellite on screen.
With the first satellite set at the strongest signal, select
Search again to find the second satellite.
• Make sure the settings are set to Two Satellites.
Changing the installation settings did not solve my
problem
• All settings, satellites and channels are only stored
at the end of the installation when you finish.
All satellite channels are gone
• If you use a Unicable system, make sure you
assigned two unique user band numbers for both
built-in tuners in the Unicable settings. It might be
that another satellite receiver in your Unicable system
is using the same user band number.
Some satellite channels seem to have disappeared
from the channel list
• If some channels seem to be gone or displaced, the
broadcaster might have changed the transponder
location of these channels. To restore the channel
positions in the channel list, you can try an update of
the channel package.
69
Page view 68
1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 113 114

Comments to this Manuals

No comments