Philips 55PUK7150 User Manual Page 68

  • Download
  • Add to my manuals
  • Print
  • Page
    / 114
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 67
installation. All installed channels are put in the
channels list All.
Unicable Setup
The Unicable System
You can use a Single Cable system, MDU or Unicable
system to connect the antenna dish to the TV. A
Single Cable system uses one cable to connect the
satellite dish to all satellite tuners in its system. A
Single Cable system is typically used in apartment
buildings. If you use a Unicable system, the TV will ask
you to assign a user band number and corresponding
frequency during the installation. You can install 1 or 2
satellites with Unicable on this TV.
If you notice some missing channels after a Unicable
installation, another installation might have been
done at the same moment on the Unicable system.
Do the installation again to install the missing
channels.
User Band Number
In a Unicable system, each connected satellite tuner
must be numbered (e.g. 0, 1, 2 or 3 etc.).
You can find the available user bands and their
number on the Unicable switchbox. User band is
sometimes shortened as UB. There are Unicable
switchboxes that offer 4 or 8 user bands. If you select
Unicable in the settings, the TV will ask you to assign
the unique user band number for each built-in
satellite tuners. A satellite tuner cannot have the same
user band number as another satellite tuner in the
Unicable system.
User Band Frequency
Next to the unique user band number, the built-in
satellite receiver needs the frequency of the selected
user band number. These frequencies are mostly
shown next to the user band number on a Unicable
switchbox.
Automatic Channel Update
If you receive digital satellite channels, you can set
the TV to automatically update these channels.
Once a day, at 6 AM, the TV updates the channels
and stores new channels. New channels are stored in
the Channels List and are marked with a
.
Channels without a signal are removed and if a
satellite operator reorders its channel package, the
channel list of the TV will be updated. The TV must
be in Standby to automatically update channels. You
can switch off Automatic Channel Update.
To switch off the automatic update…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation > Automatic
Channel Update and select Off.
3 - Press
(left) repeatedly if necessary, to close
the menu.
You can set the TV to only update the channels of a
specific satellite.
To mark satellites for updating…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation and
select Automatic Update Option. In the list of
satellites, select a satellite to mark or unmark.
3 - Press
(left) repeatedly if necessary, to close
the menu.
In certain countries, the automatic channel update is
done while watching TV or on any moment when the
TV is in Standby.
Manual Channel Update
You can always start an channel update yourself.
To start a channel update manually…
1 - Press
, select All Settings and press OK.
2 - Select Satellite Installation > Search for
Channels and select Update Channels.
3 - Follow the instructions on screen. The update
may take a few minutes.
Add a Satellite
You can add an additional satellite to your current
satellite installation. The installed satellites and their
channels remain untouched. Some satellite operators
do not allow adding a satellite.
The additional satellite should be seen as an extra, it
is not your main satellite subscription or not the main
satellite of which you use its channel package.
Typically, you would add a 4th satellite when you
have 3 satellites already installed. If you have 4
satellites installed, you might consider removing one
first to be able to add a new satellite.
Setup
If you currently have only 1 or 2 satellites installed, the
current installation settings might not allow adding an
extra satellite. If you need to change the installation
settings, you must redo the complete satellite
installation. You cannot use Add satellite if a change
of settings is needed.
68
Page view 67
1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 113 114

Comments to this Manuals

No comments