Philips CEM250/98 User Manual
Browse online or download User Manual for Car media receivers Philips CEM250/98. Philips CEM250/98 User manual
- Page / 1
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Register your product and get support at
CEM250
EN Quick Start Guide
1
ab
efg
c
34
2
B
b
a
c
d
aa
b
c
d
a
b
e
f
c
d
g
h
i
b
c
d
h
d
Overview of parts
1
These are the supplied parts needed to
connect and install this unit.
1 In-car audio system
2 Sleeve
3 Front panel
4 Standard connector
5 Trim plate (1 pieces)
6 Rubber cushion
7 Disassembly tools
8 Screws 4 pieces
Connect wires
Caution
Ensure that all loose leads are insulated with
•
electrical tape.
For cars with ISO connectors
2 3
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 MIC Microphone
2 FRONT
LINE OUT
R
Front right speaker
3 FRONT
LINE OUT
L
Front left speaker
4 REAR LINE
OUT R
Rear right speaker
5 REAR LINE
OUT L
Rear left speaker
6 SUB OUT Subwoofer
7 ANTENNA Antenna
For cars with ISO connectors
3 4
Caution
Be sure to connect the black ground (earth)
•
lead fi rst.
1
Connect the antenna and amplifi er as
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
3
Check the car’s wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
the unit.
1 Green/black
strip
Left speaker
(Rear)
2 White/black
strip
Left speaker
(Front)
3 Gray/black
strip
Right speaker
(Front)
4 Purple/black
strip
Right speaker
(Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Orange/
white
Illumination switch
i YELLOW To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount •
the unit into a car.
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car •
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected, •
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Remove the mounting sleeve with the
supplied disassembly tools.
4
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
5
Place the rubber cushion over the end of
the bolt.
6
Slide the unit into the dashboard until you
hear a click sound.
7
Reconnect the negative terminal of the car
battery.
Attach the front panel 5
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
4
Release the panel to engage the left side.
Turn on
1
Press
z
to turn on the unit.
• To turn off the unit, press
z
for 3
seconds.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press
3
or
4
repeatedly to until the cur-
rently time is displayed.
3
Tur n
z
clockwise to set hour.
4
Press
z
to confi rm.
5
Tur n
z
anti-clockwise to set minute.
6
Press
z
to confi rm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Tuner.
2
Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press
∞
or
§
to tune to a radio station
manually.
To search for a radio station •
automatically, press SEARCH for 3
seconds.
5
5mm
5mm
Pairing bluetooth devices
You can pair your bluetooth device with the unit
as follows:
1 Turn on bluetooth function on the device.
2 Setup bluetooth fuction on your device.
3 Select “CEM250” in the pairing list.
4 Enter default password “0000”.
» “ [CONNECT] ” is displayed on the
panel if pairing succeeds.
5 Press and hold SOURCE to disconnect
Bluetooth connection.
Note
Y
• ou can hold SOURCE again to reconnect
last used Bluetooth device.
Make a call
1 Press SOURCE repeatedly to select BT
MUSIC.
2 Press .
3 Press or to select from the following
list:
DIAL NUM• : dial number directly
DIALLED• : dialed number
MISSED• : missed call
RECEIVED• : received call
ME PBK• : Phone directory
SIM PBK• : SIM directory
4 Press to confi rm the selection.
To dial a number directly, select DIAL NUM.
1 Press 0-9 to enter phone number.
Press •
/ to change a number.
Press •
to reset entered numbers.
2 Press to dial.
To use a number in call log or directory, select the
option other than DIAL NUM.
1 Tur n to select a number from call log or
directory.
2 Press to dial.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CEM250_98_QSG_V2.0
CEM250_98_QSG_V2.0.indd 1CEM250_98_QSG_V2.0.indd 1 2009-10-15 11:37:532009-10-15 11:37:53
1
Summary of Contents
Page 1 - All rights reserved
Register your product and get support atCEM250 EN Quick Start Guide 1abefgc342Bbacdaabcdabefcdghibcdhd Overview of parts 1These are the supplied
More documents for Car media receivers Philips CEM250/98
Philips CEM250/98 User Manual
(34 pages)
Related products and manuals for Car media receivers Philips CEM250/98
(2 pages)
(23 pages)
(39 pages)
(70 pages)
(25 pages)
(2 pages)
(4 pages)© 2020, manymanuals.com. All rights reserved. | 1.698 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals