Document No. DOC-IWS-712C, Rel. 6-2008 M1500 / M1500T 15.0” XGA TFT NEMA 4/12 Flat Panel Monit
10 32131 2TOP VIEWFRONT VIEWPHOENIX CONTACT P.N. 1777992Connecting Power The M1500 monitor is powered from 100-240 VAC, 50/60 Hz or optionally from
11 SERIALRS-232VGAUSB"B"USB RETENTION BRACKETDVI-DTOUCH SCREEN CABLESVIDEO CABLES(AUTO ADJ)MENUDOWNSELECT UP(VGA / DVI)POWER Connection o
12 Turning on the Computer and Monitor With power applied to the monitor and all cables connected you may power up the computer and press the POWER
13 POWER(VGA / DVI)UPDOWN(AUTO ADJ)SELECTMENUPOWERMENUDOWN(AUTO ADJ)SELECT(VGA / DVI)UPChapter 3. - Monitor OSD and Settings On Screen Display (OSD)
14 Button and LED Functions BUTTON FUNCTION POWER Pressing this button once wakes the monitor up. Pressing the POWER button again turns off the b
15 OSD Menus and Settings MAIN MENU The following section describes the monitor’s OSD menus and settings. With the monitor powered up
16 Pressing the SELECT button will cause the following screen to be displayed: Pressing the UP and DOWN buttons will adjust the bri
17 COLOR With COLOR highlighted on the MAIN MENU pressing SELECT will cause the following screen to be displayed: PRE
18 POSITION With POSITION highlighted on the MAIN MENU, pressing SELECT will cause the following screen to be displayed:
19 HORIZONTAL With HORIZONTAL highlighted on the POSITION menu, pressing SELECT will cause the following screen to be displayed:
2 Revision List WARRANTY Nematron warrants to Customer that the Products will be free from defects in material a
20 0 1 2 3 4 SETUP OSD POSITION With SETUP highlighted on the MAIN MENU pressing SELECT will cause the following screen to be displaye
21 Pressing SELECT again will deselect the OSD POSITION adjustment menu and the setting will be saved. OSD TIME With OSD TIME highlighted on
22 INPUT SOURCE With INPUT POSITION highlighted on the SETUP menu, pressing SELECT will cause the following screen to be displayed:
23 OSD Message Displays OUT OF FREQUENCY The following OSD message will appear if the horizontal or vertical refresh rate of the incoming video s
24 POWER SAVER MODE The following message appears when the monitor is on but in DPMS (Display Power Management Signaling) mode. This
25 Appendix VGA Input Pin Assignment DVI-D Pin No. Name Description 1 TMDS DATA2- TMDS DATA2 Differential Negative Signal 2 TMDS DATA2+ TMDS DAT
26 Analog 15- Pin D-Sub Pin No. Name Description 1 Red Red Analog Data 2 Green Green Analog Data 3 Blue Blue Analog Data 4 GND Ground 5 GND Grou
27 1 243USB-B CONNECTOR ON REAR OF MONITORTouch Screen Pin Assignment Serial RS-232 Pin No. Name Description 1 DCD Data Carrier Detect 2 RX Rec
3 Table of Contents WARRANTY ...
4 Chapter 1 - Introduction The M1500 is a high performance 15” color TFT flat panel monitor specifically designed for harsh industrial environment
5 Specifications DISPLAY TOUCH SCREEN (Optional) Touch Screen Technology 5- Wire Analog Resistive Interface USB 1.1 and Serial RS-232 Resolution
6 ENVIROMENTAL Operating Temperature 0C to 50C Operating Humidity 20% to 80% RH, noncondensing Operating Shock 15g peak acceleration, 11msec Oper
7 12315.80" 2.40" 2.65" 12.80" 1.17" 3.95" Front and Side Views of Monitor
8 15.0" ±.02"12.0" ±.02"Chapter 2 - Installation of Monitor This monitor is intended to be mounted in and used where
9 UPMENU DOWNSELECT POWERFRONT PANEL OF NEMA ENCLOSURETIGHTEN TO 8 INCH-POUNDSCOMPRESSABLE NEMASEALING GASKET .25" THICK MONITOR FRONT BEZEL MA
Comments to this Manuals