Philips 201P User Manual

Philips 201P Electronic User's Manualfile:///G|/manual/english/201P/index.htm [10/16/1999 6:36:02 AM]

Brightness hotkey. When both the LEFT and RIGHT arrows are pressedat the same time, then the adjustment controls for BRIGHTNESS willshow up.LEFT and R

1. D-Sub Port - Attach the D-Sub connector that comes with your monitor here.Other end connects to your PC.2. Power in - Attach power cable here.3. US

On-Screen DisplayDescription of the On-Screen Display • The OSD Tree • The OSD ControlsDescription of the On Screen DisplayWhat is the On-Screen Displ

RETURN TO TOP OF THE PAGEThe OSD TreeBelow is an overall view of the structure of the On-Screen Display. You can use this as reference when youwant to

On-Screen Displayfile:///G|/manual/english/201P/osd/osddesc.htm (3 of 4) [10/16/1999 6:36:11 AM]

RETURN TO TOP OF THE PAGE On-Screen Displayfile:///G|/manual/english/201P/osd/osddesc.htm (4 of 4) [10/16/1999 6:36:11 AM]

Customer Care & WarrantyPLEASE SELECT YOUR COUNTRY TO READ THE WARRANTY COVERED:WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Ge

GlossaryA B C D E F G H I J K L M N O P Q R S T U V W X Y ZAAutoscanA microprocessor-based feature of Philips Brilliance monitors is able to detect au

CCE MarkCE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance withEuropean Community safety, EMI and EMS re

Points where convergence error is specified. Convergence-error correctionA method of correcting for convergence error to insure that all three beams l

Safety and Troubleshooting InformationSafety Precautions and Maintenance • Troubleshooting • Regulatory Information • OtherRelated InformationSafety p

DDC is a communication channel for displays and computers. The DDC feature allows the monitor controllerto be automatically configured to make optimal

Dot rateFrequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between thevideo card and subsequent processin

In 1991, the Swedish Tjänstemannens Central Organization (TCO, Swedish confederation of ProfessionalEmployees ) set a standard even more severe than M

Also called line frequency and expressed in kHz, it is the number of video lines written on the screen everysecond (from left to right). The higher th

LLinearityThe degree to measure the actual location of a pixel on the screen corresponds with its intended location. (see figure ) Line frequencySee

MMoiré effectA fringe pattern arising from the interference between two superimposed line patterns.In a monitor it comes from the interference between

screen area, resulting in an image that is smaller (and less legible) than it needs to be.RETURN TO TOP OF THE PAGE PParallelogram DistortionSee Geome

RRasterThe area on screen that electron beam can reach. Refresh rateSee Vertical scanning frequency. ResolutionThe number of pixels that can be displ

Anti-Static coatingsDue to bombardment by beam electrons, monitor screens become electrically charged when in use.Electrically charged screens surface

The ARAS coating reflects only about 0.5% of the incident light. AGRAS (Anti-Glare anti-Reflection Anti-Static) coating.A combined anti-reflection, an

About This Electronic User's ManualAbout This Guide • Other Documents You May Need • Notational DescriptionsAbout This GuideThis electronic user&

SOG (Synchronization On Green)A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse,red colo

See rotation function. Trapezoid distortionSee Geometrical distortion. TTL signalA TTL (Transistor-transistor-logic) signal is a digital signal level

signaling.A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-controlledswitch between the upstream port a

VVertical dot pitchSee Dot pitch. Vertical scanning frequencyExpressed in Hz, this is the number of fields written to the screen every second in inte

resolutions from 1280 x 1024 to 1600 x 1280, horizontal line frequencies up to 90 kHz and bandwidths up to200 MHz. VIS (Viewable Image Size)The real s

Download and PrintThis page provides an option to read the manual in .pdf format. PDF files can be downloaded into your harddisk, then viewed and prin

201B.pdf201P.pdfDownload and Printfile:///G|/manual/english/download/download.htm (2 of 2) [10/16/1999 6:36:13 AM]

TroubleshootingSafety Precautions and Maintenance • Troubleshooting • Regulatory Information• Other Related InformationCommon ProblemsHaving trouble?

Dim PictureAdjust the Brightness and Contrast controls.● Check your video card and it's owner's manual instructions for itmay be a non-VES

Regulatory InformationTCO'92 and TCO '99 Information • TCO Environmental Requirements • Energy StarDeclaration • Federal Communications Comm

Notes, Cautions, and WarningsThroughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.These bloc

This product meets the requirements for the TCO'99 scheme which provides for international andenvironmental labeling of personal computers. The l

Cadmium**Cadmium is present in rechargeable batteries and in the color-generating layers of certain computerdisplays. Cadmium damages the nervous syst

Normal operation ON Green Typical 124 WPower SavingPosition A1Suspend Yellow < 7 WPower SavingPosition A2OFF Amber < 2.8 WAs an ENERGY STAR® Par

RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration)Cet équipement a été testé et déclaré conforme auxlimites des appa

RETURN TO TOP OF THE PAGEVCCI Notice (Japan Only)This is a Class B product based on the standard of the Voluntary Control Council for Interference (V

Polish Center for Testing and Certification NoticeThe equipment should draw power from a socket with an attached protection circuit (a three-prong soc

Placering/VentilationVARNING:FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄRDU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/VentilationAD

Ergonomie Hinweis (nur Deutschland)Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durchRöntgens

of plug proceed as follows:1. Remove fuse cover and fuse.2. Fit new fuse which should be a BS 13625A,A.S.T.A. or BSI approved type.3. Refit the fuse c

the lead - not simply over the three wires. RETURN TO TOP OF THE PAGERegulatory Informationfile:///G|/manual/english/201P/safety/regs/regulat.htm (11

Product InformationProduct Features • Technical Specifications • Automatic Power Saving • PhysicalSpecification • Pin Assignment • Product ViewsProduc

Other Related InformationSafety Precautions and Maintenance • Troubleshooting • Regulatory Information •Information for Users in the U. S. • Informati

PCUH411 USB Hub (Option)Front View • Rear View • Installing your USB HubInstalling your USB HubInstalling on aconventional base.1. Take out the USBhub

6. Position the USBhub to the back of theMultimedia Pedestal. 7. Attach the USB hubby sliding-in to theMultimedia base.RETURN TO TOP OF THE PAGEUSB Hu

The OSD ControlsDescription of the On-Screen Display • The OSD Tree • ICEadjust Software ProgramThe OSD Controls : Brightness (HotKey) • Contrast (Hot

seconds the BRIGHTNESS window will disappear with the new adjustment saved.SmartHelpAfter the BRIGHTNESS window has disappeared, to continue to the CO

RETURN TO TOP OF THE PAGELANGUAGEThe ON SCREEN DISPLAY shows its settings in one of five languages. The default is English, but you canselect French,

4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAINCONTROLS will be highlighted...SmartHelpAfter returning t

4) Press the or button to highlight INPUT B or INPUT A.5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSEMA

3) Press the button. The ZOOM window appears.4) Press the or button to adjust ZOOM.5) Press the button to confirm your selection and return to the

ADJUST HORIZONTALADJUST POSITION under ADJUST HORIZONTAL shifts the image on your screen either to the left or right.Use this feature if your image do

• Video dot rate 320 MHz• Input impedance- Video 75 ohm- Sync 2.2 kOhm• Input signal levels 0.7 Vpp• Sync input signalSeparate syncComposite sync• Syn

4) Press the or button to move the image to the left or right.5) When the position is adjusted, press the button to return to MAIN CONTROLS window,

2) Press the button until ADJUST VERTICAL is highlighted.3) Press the button. The ADJUST VERTICAL window appears. ADJUST POSITION should behighligh

6) To adjust the vertical size, press the or button.7) When the size is adjusted, press the button to return to MAIN CONTROLS window. CLOSE MAINCON

3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should behighlighted.4) Press the button. The SIDE CURVE window appears. PIN

5) To adjust the pincushion, press the or button.6) When the pincushion is adjusted, press the button to highlight BALANCED or press the buttonto

SmartHelpAfter returning to MAIN CONTROLS . . ...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST SIDE ANGLESand follow the directio

4) Press the button to highlight ADJUST SIDE ANGLES.5) Press the button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted.6) To adjus

8) To adjust the parallelogram, press the or button.9) When the parallelogram is adjusted, press the button to return to the ADJUST SHAPE window.BA

3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should behighlighted.4) Press the arrow until ROTATE IMAGE is highlighted.5)

6) To adjust the rotation, press the or button.7) When the rotation is adjusted, press the button to return to the ADJUST SHAPE window. BACK TOMAIN

RETURN TO TOP OF THE PAGEPhysical Specifications • Dimensions19.7" x 19.7" x 18.3" / 501 x 501 x 466 mm (including base)19.7" x 1

3) Press the button. The ADJUST COLOR window appears.4) Press the or button to highlight 9300K for GENERAL USE, 6500K for IMAGE MANAGEMENT,5500K fo

6a) If USER PRESET is highlighted, press the button to highlight RED. Next, press the orbutton to adjust the color red.6b) When finished with RED, p

RESET TO FACTORY SETTINGSRESET TO FACTORY SETTINGS returns everything in all the windows to factory presets.1) Press the button on the monitor. The M

SmartHelpAfter returning to MAIN CONTROLS . . .. . . to continue to EXTRA CONTROLS, press the button until EXTRA CONTROLS ishighlighted. Next, start w

4) To degauss your screen, press the button. Your screen will be degaussed, then the MAINCONTROLS window will reappear. CLOSE MAIN CONTROLS will be h

3) Press the button. The EXTRA CONTROLS window appears. DEGAUSS will be highlighted.4) Press the button until ADJUST MOIRE is highlighted.5) Press t

6) To adjust the horizontal moire, press the or button.7) When the moire is adjusted, press the button to return to the EXTRA CONTROLS window. BAC

3) Press the button. The EXTRA CONTROLS window appears. DEGAUSS is highlighted. Note: If youhave not degaussed the monitor, please follow the steps

6) To adjust the horizontal convergence, press the or button.7) When the horizontal convergence is adjusted, press the button to highlight VERTICA

ADJUST PURITY (Not available in all models)EXTRA CONTROLS is a set of features, including ADJUST PURITY. Purity is a process by which colorsappear cl

4Identical output - connectedto pin 1012 Serial data line (SDA)5 Ground 13 H. Sync / H+V6 Red video ground 14 V. Sync (VCLK for DDC)7 Green video grou

5) Press the . The ADJUST PURITY window appears. TOP LEFT is highlighted.6) To adjust the top left purity, press the or button.7) When the top lef

8) To adjust the top right purity, press the or button.9) When the top right purity is adjusted, press the button to highlight BOTTOM LEFT.10) To

12) To adjust the bottom right purity, press the or button.13) When the bottom right purity is adjusted, press the button to return to the EXTRA C

3) Press the button. The EXTRA CONTROLS window appears. DEGAUSS will be highlighted.4) Press the button until AUTO CALIBRATE is highlighted.5) Pres

7) Press the button to exit the MAIN CONTROLS window.SmartHelpAfter returning to MAIN CONTROLS . . .. . . to exit completely, press the button. RE

Your International Philips F1rst Choice WarrantyThank you for purchasing this Philips monitor.All Philips monitors are designed and manufactured to hi

Your International GuaranteeDear Customer,Thank you for purchasing this Philips product which has been designed and manufactured to the highestquality

LIMITED WARRANTY (Computer Monitor) Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange**Product will be exchanged with a n

Philips service organization will attempt to provide service (although there may be a delay if the appropriatespare parts and technical manual(s) are

Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601Your International Philips F1rst Choice WarrantyThank you for purchasing this Philips

Installing your MonitorFront View • Rear View • PCUH411 USB Hub (option)Front ViewPower button switches your monitor on.OK button which when pressed w

F1rst Choice Contact InformationTelephone numbers:Austria0660 311 657*Luxembourg0800 30 12Belgium0800 735 75Netherlands0800 023 2011Cyprus0809 22 56No

Consumer Information CentersAntilles ¥ Argentina ¥ Australia ¥ Bangladesh ¥ Brasil ¥ Canada ¥ Chile ¥ China ¥ Colombia¥ Czech Republic ¥ Dubai ¥ Egypt

TURKEYTürk Philips Ticaret A.S.Talatpasa Caddesi No 5.80640-Gültepe/IstanbulPhone: (0800)-211 40 36Fax : (0212)-281 1809Latin AmericaANTILLESPhilips A

COLOMBIAIndustrias Philips de ColombiaS.A.-Division de ServicioCalle 13,No 51-39Apartado 4282, BogotaPhone: (01)-6235511/ 9800-18971 (toll free)Fax :

VENEZUELAIndustrias Venezolanas Philips S.A.Apartado Postal 1167Caracas 1010-APhone: (02) 2377575Fax : (02) 2376420CanadaCANADAConsumer Service Divisi

BANGLADESHPhilips Service Centre100 Kazi Nazrul IslamAvenue Kawran Bazar C/ADhaka-1215Phone: (02)-812909Fax : (02)-813062CHINABEIJINGBeijing Authorize

HONG KONGPhilips Hong Kong LimitedConsumer Information Centre16/F Hopewell Centre17 Kennedy Road, WANCHAIPhone: 2821-5345Fax : 2861-3104INDIABOMBAYPhi

JAPANPhilips Consumer Electronics1-11-9,EbisuminamiShibuya-KuTokyo 150Phone: (03)-3719-2235Fax : (03)-3715-9992KOREAPhilips Korea Ltd.Philips HouseC.P

PHILIPPINESPhilips Electronics and Lighting Inc.106 Valero St., Salcedo VillageMakati, Metro Manilla.Phone: (02)-8100161Fax : (02)-8173474SINGAPOREPhi

SOUTH AFRICASouth African Philips.S.V. Div. 195 Main R.D.Martindale., JohannesburgP.O.box 58088Newville 2114Phone: (011)-4715000Fax : (011)-4715034Mid