Philips Mercury 1012L2S User Manual download pdf

NOTE: Other World Computing declares that this processor upgrade

has been tested and found to comply with the limitations of a Class B

digital device, pursuant to Part 15 of the FCC Rules & Regulations. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed in

accordance with these instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in any one particular installation, If this equipment does

cause harmful interference to radio or television reception, this can be

determined by turning the equipment this upgrade is installed into on and

off. If this is determined to be the cause of harmful interference, the end

user is encouraged to attempt to correct the interference by one or more

of the following procedures:

• Connect the equipment to another electrical outlet, or use a line ﬁ ltering

device between the outlet and the computer

• Move the location of the receiving device and the computer

• Reorient the receiving antenna

• Increase the distance separating the receiver and the computer

OWC Mercury Extreme G4

Installation Manual

9. Remove Processor

10. Remove Protective Cover

11. Insert Processor - All Systems

Optional - Jumper Settings - Adjustment NOT necessary!

FCC Statement

Troubleshooting Tips:

Contact Information:

Installation of the processor daughtercard is the same on all

systems, simply align the 3 screw holes in the card and gen-

tly place over the logic board. Gently but ﬁ rmly press straight

down on the two rearmost screwholes until you feel the card

“click” into place. Insert the included screwdriver and tighten

the encapsulated 3 Phillips screws into the 3 screw holes.

You’re all done - Enjoy your new processor!

Remove the protective cap from the OWC Mercury Extreme

G4 processor upgrade. The cap is located on the bottom of

the card, between the screw holes. Place the cap onto the

processor card you just removed.

Place your ﬁ ngers gently underneath the edge of the

processor daughtercard, and with your ﬁ ngertips, pull straight

up. Do not pull at an angle, you risk breaking the processor

socket if you don’t pull straight up.

Boot Issues:

• Make certain you updated the ﬁ rmware to version 4.2.8. If you did not,

you will have to reinstall your original processor and boot into Mac OS 9

to perform this task.

• Press the reset button marked “S1” on the logic board. This is located

on the corner of the logic board near the PCI slots on most machines.

You will need to reset your date & time settings as well as any AppleTalk

settings after doing this.

• Reset the PRAM on your computer by pressing and holding the

command - option - P and R keys at startup until the machine chimes

3 times. You will need to reset your date & time settings as well as any

AppleTalk settings after doing this.

Final Cut Pro 3 and 4 Issues / Full Switch Setting Chart:

• Final Cut Pro requires a valid speed to be reported correctly by Apple

System Proﬁ ler. For detailed instructions about this issue, please visit our

tech center at: http://eshop.macsales.com/tech_center/index.cfm

This page also includes a full switch setting chart for your convenience.

Sleep Issues:

• The OWC Mercury Extreme G4 supports hard disk and display sleep in

all conﬁ gurations. With some system conﬁ gurations, deep sleep may not

be supported.

Sales: 800.275.4576

International: 815.338.8658

Customer Service: 800-275-4576

Tech Support: 815-338-8685

24hr Fax: 815.338.4332

For support via email submit your question here:

http://eshop.macsales.com/Service/Tech.cfm

Sales & Technical Support Hours (CST)

8:30AM-8PM Monday - Friday

10AM-4PM - Saturday

Customer Service Hours (CST)

8:30am-5:30pm Monday - Friday

OWC product warranties are non-transferrable

Other World Computing 1004 Courtaulds Drive Woodstock, IL 60098

There is no need to modify the settings on the accelerator as

they are preset for maximum performance from the factory.

If you wish to adjust, please follow this chart.

NOTE: See Troubleshooting section for Final Cut Pro issues.

OWCMANMEG4

1 2

Summary of Contents

Page 1 - Installation Manual

NOTE: Other World Computing declares that this processor upgrade has been tested and found to comply with the limitations of a Class B digital device,

Page 2

1. Items Needed:2. System Requirements:3. Firmware Upgrade4. Remove Heatsink (AGP Graphics & Gigabit Ethernet)8. Remove Processor Card (QuickSilve

Comments to this Manuals

No comments

Philips Mercury 1012L2S User Manual

Browse online or download User Manual for Hardware Philips Mercury 1012L2S. Philips Mercury 1012L2S User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Philips Mercury 1012L2S