Philips SWS2083W-17 User Manual download pdf

Operating Instructions

Mast Mounted Outdoor Antenna Amplifier

Installation Instructions

1. Place pre-amplifier unit on the antenna mast approxi

mately 3 feet below the antenna.

2. Use mast clamp and wing nuts provided to secure the

pre-amplifier unit to the mast.

3. Connect the antenna terminals to the input terminals of

the pre-amplifier unit. This connection may be made using

either 300 ohm twin lead or 75 ohm coaxial cable. See

below for specific instructions.

300 ohm Twin Lead

__________________

Split 300 ohm lead about 6 inches and then strip off 1 inch

of insulation on each end of the lead. Attach one end of

the lead wire to the antenna and the other end to the pre

amplifier inputs.The pre-amplifier input terminals are

reached by removing the weatherproof cover. This can be

done by loosening (not removing) the cover lock screws

and lifting off the weatherproof cover. Attach the leads to

the 300 ohm terminals, be sure to place the wire under the

hold down (see illustration).

300 ohm Terminals

Pre-Amplified Unit«,

(top view with

cover removed)

Cover Lock'

Screw

Hold Down Screws -

inrpw«; ^ I

!*■ Outdoor

Antenna

” 300 ohm Wire

" Washers

Wing Nuts

■ Attach wires to terminals with

wires BETWEEN washers

■ Tighten wing nuts

—^1

---------------

----------

300 ohm Wire

»Split antenna lead-in wire about six inches

• Strip insulation back about one inch

Connect to 300 ohm terminals

O O

Connect 75 ohm coaxial

cable to outdoor antenna

Pre-Amplitier Unit

, Outdoor Matching

’ Transformer

(not supplied)

75 ohm Coaxial Cable

Use an outdoor matching transformer (not included)

to attach the coaxial cable to the antenna terminals. There

are two ways to attach the coaxial cable to the pre

amplifier unit.

1. Use another matching transformer to attach the coax

cable to the terminals marked 300 ohm.

2. Strip back the outer jacket 2.5 inches. Then twist the

braid to form a lead. Cut off 1 inch of the inner foam in

sulation exposing the center conductor. Place the coaxial

cable under the hold down and connect the center con

ductor under the left hand terminal and the braid under

the right hand terminal.

Pre-Amplifier Unit

(top view with cover removed)

300 ohm Terminals

Center Conductor

75 ohm Terminal

■ Hold Down

75 ohm Coax

1 2 3 4

Summary of Contents

Page 1 - Operating Instructions

Operating InstructionsMast Mounted Outdoor Antenna AmplifierInstallation Instructions1. Place pre-amplifier unit on the antenna mast approximately 3

Page 2 - Performance Specifications:

Connection:Pre-Amplifier to AmplifierThere is a slide switch on base of pre-amplifier unit, from 75 ohm to 300 ohm which is used to seiect cable type

Page 3 - Instrucciones para el Usuario

Instrucciones para el UsuarioAmplificador de antena exterior para instalar sobre mástil______________________________Instrucciones de instalación

Page 4 - Especificaciones:

Conexión:Entre preamplificador y amplificadorHay un interruptor corredizo en la base del preamplificador, que sirve para cambiar de 75 a 300 ohm y par

Philips SWS2083W-17 User Manual

Browse online or download User Manual for Accessories for video Philips SWS2083W-17. Philips SWS2083W-17 User Manual

Summary of Contents

More documents for Accessories for video Philips SWS2083W-17

Comments to this Manuals

Philips SWS2083W-17 User Manual

Browse online or download User Manual for Accessories for video Philips SWS2083W-17. Philips SWS2083W-17 User Manual

Summary of Contents

More documents for Accessories for video Philips SWS2083W-17

Comments to this Manuals

Related products and manuals for Accessories for video Philips SWS2083W-17