Philips Colour Television Specifications download pdf (Page 26)

Service Modes, Error Codes and Fault Finding

GB 26 EM3E5.

– M38.9: NTSC M signal received with video carrier on

38.9 MHz

• Line 19 - Audio System Gives information about the

audio system of the selected transmitter.

– Sound Muted: No sound

– Dolby Pro Logic: Dolby Pro Logic sound received

– Mono: Mono sound received

– Stereo: Stereo sound received

– Dual I: Language I received

– Dual II: Language II received

– Digital Mono: Digital mono sound is received

– Digital Stereo: Digital stereo sound is received

– Digital Dual I: Digital language I is received

– Digital Dual II: Digital language II is received

• Line 20 - Tuned bit Gives information about the tuning

method of the stored pre-set. If a channel is found via

’automatic installation’ you will see the value 'Off'. When

you change this (automatically found) frequency via ‘fine

tune’ adjustment (installation menu - manual installation),

the displayed value will change to ‘On’. So when you see

the value ‘On’ in this line, it is an indication that the

received channel is a non-standard signal (e.g. of a

VCR).

• Line 21 - Speaker config. Gives the speaker

configuration settings. In case the set is a non-Dolby set,

it displays '0'. If it is a Dolby-set, it displays: 'FULL

INTERNAL', 'L/R EXTERNAL', 'SURROUND

EXTERNAL' or 'FULL EXTERNAL'. Change the speaker

configuration (for a Dolby-set), via the 'CURSOR LEFT'

and 'CURSOR RIGHT' keys on the RC-handset after

opening the ‘INSTALLATION’ menu and selecting

'SETUP'. Open the ‘INSTALLATION’ menu by pressing

the 'TIMER' and 'ENLARGE' buttons at the same time.

• Line 22 - Digital Sources Gives the configuration

setting for the digital source. It displays: 'FRONT', 'EXT1',

'EXT2', ‘EXT3’ or 'NONE'. If one of these is selected, the

starting point is a top quality signal on that input and a

number of settings are therefore changed automatically.

Change the digital source via the 'CURSOR LEFT' and

'CURSOR RIGHT' keys on the RC-transmitter after

opening the installation menu and selecting 'SETUP'.

The installation menu can be opened by pressing

'TIMER' and 'ENLARGE' at the same time.

How to exit CSM

Use one of the following methods:

• After you press a key on the RC-transmitter (with

exception of the ‘CHANNEL’ and ‘VOLUME’ keys), or

• After you switch the TV-set ‘OFF’ with the mains switch.

5.3 Problems and Solving Tips (related to CSM)

Note: Below described problems are all related to the TV

settings. The procedures to change the value (or status) of

the different settings, are described above.

The new value(s) are automatically stored.

5.3.1 Picture Problems

Worse picture quality in case of DVD pictures

Check line 22 'Digital sources'. In case line 22 gives the

indication 'Not Present', change the setting into 'Present' (via

the ‘installation’ menu).

Snowy/noisy picture

1. Check line 15 'Noise Figure'. In case the value is 127 or

higher and the value is also high on other programs,

check the aerial cable/aerial system.

2. Check lines 9 'Sharpness' and 15 'Noise Figure'. In case

the value of line 9 is 3 or 4 and the value of line 15 is high

(127 or higher), decrease the 'Sharpness' value.

Picture too dark

1. Press 'Smart Picture' button on the RC-transmitter. In

case the picture improves, increase the ‘Brightness’ or

the ‘Contrast’ value. The new value(s) are automatically

stored (in ‘personal’ pre-set) for all TV channels.

2. Check lines 5 'LS Brightness' and 6 'LS Contrast'. If the

value of line 5 is low (< 10) or the value of line 6 is low

(< 10), increase the ‘Brightness’ or the ‘Contrast’ value.

Picture too bright

1. Press 'Smart Picture' button on the RC-transmitter. In

case the picture improves, decrease the ‘Brightness’ or

the ‘Contrast’ value. The new value(s) are automatically

stored (in ‘personal’ pre-set) for all TV channels.

2. Check lines 5 'LS Brightness' and 6 'LS Contrast'. If the

value of line 5 is high (> 40) or the value of line 6 is high

(< 50). Decrease the ‘Brightness’ value or increase the

‘Contrast’ value.

White line around picture elements and text

1. Press 'Smart Picture' button on the Remote Control. In

case the picture improves, decrease the ‘Sharpness’

value. The new value is automatically stored (in

‘personal’ pre-set) for all TV channels.

2. Check line 9 'Sharpness'. Decrease the ‘Sharpness’

value. The new value is automatically stored for all TV

channels.

No picture

Check line 20 'Tuned bit'. In case the value is ‘On’, install the

required program again. Open the installation menu by

pressing 'timer' and 'enlarge' at the same time and perform

manual installation.

Blue picture

No proper signal is received. Check the aerial cable/aerial

system.

Blue picture and/or unstable picture

A scrambled or decoded signal is received.

Black and white picture

Check line 7 'LS Colour'. In case the value is low (< 10)

increase the ‘Colour’ value. The new value is automatically

stored for all TV channels.

No colours/colour lines around picture elements

1. Check lines 17 'Colour System' and 18 'TV System'. If a

‘strange’ system pop’s up, something has gone wrong

during installation. Re-install the channel.

2. In case line 17 is ‘PAL’ and line 18 is ‘L’, the installed

system for this pre-set is ‘France’, while ‘West Europe’ is

required. Install the required program again: open the

installation menu by pressing 'timer' and 'enlarge' at the

same time and perform manual installation. Select

system ‘West Europe’.

Colours not correct

Check lines 17 'Colour System' and 18 'TV System'. In case

line17is‘PAL’ andline18is‘L’, the installed system for this

pre-set is ‘France’,while‘West Europe’ is required. Install the

required program again: open the installation menu by

pressing 'timer' and 'enlarge' at the same time and perform

manual installation. Select ‘System; West Europe’.

Colours not correct/unstable picture

Check lines 17 'Colour System' and 18 'TV System'. In case

line17is‘SECAM’ and line 18 is ‘BG’, the installed system

for this pre-set is ‘West Europe’, while ‘France’ is required.

Install the required program again: open the installation

menu by pressing 'timer' and 'enlarge' at the same time and

perform manual installation. Select ‘System; France’.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 62 63

Comments to this Manuals

No comments

Philips Colour Television Specifications Page 26

Comments to this Manuals

Related products and manuals for TVs & monitors Philips Colour Television