Philips 8P6054C Service Manual

GENERAL INFORMATION CAUTION: A SEPARATE ISOLATION TRANSFORMER MUST BE USED WHEN SERVICING THIS CHASSIS. PTV 800 PANEL INFORMATION Models Covered in

LARGE SIGNAL PANEL The large signal panel contains the SMPS (Switch Mode Power Supply), Scan-derived Power Supply, Horizontal and Vertical deflection

The pulse from T402 Pin 1 is rectified by D405 and provides the run voltage for IC401 Pin 16. This rectified run voltage is also applied to IC401 Pin

from D417 is applied through F409, and a voltage divider network R450, R451, and R452 to pins 3, and 1 of IC402 for over-voltage, and under-voltage sh

Guide Plus - Smart Clock Guide Plus or Gemstar is a menu-driven broadcast information service broadcast on ABC affiliate stations. (Figure 4) TV guid

7) will turn On, turning Q500 Off, turning Q503 Off. This turns Q502 On, which turns Q904 On. This will turn Q903 On hard increasing the voltage on

TROUBLESHOOTING CAUTION: THIS CHASSIS REQUIRES THE USE OF AN ISOLATION TRANSFORMER WHILE TROUBLESHOOTING. Switch Mode Power Supply Since there are

No 130 volt supply 1. With 120 volts ac applied, ground Pin 16 of IC402 to bypass the microprocessor. If the full power supply turns on, troublesho

Horizontal Drive The Horizontal Drive signal from the Small Signal Panel is fed to the base of Q803, the Horizontal Pre Driver. (Figure 5) The output

Vertical Deflection Vertical Sync from the Small Signal Panel is applied to the Large Signal Panel via J601 Pins 2 and 7 and is applied to IC551 Pin

High Voltage/Beam Limiting/Shutdown Circuits The Horizontal Pulse from the Horizontal Output transformer T801 Pin 7 is applied to the Sync Pulse Inve

MODEL TO PANEL LIST • The Model to Panel List shown below identifies all electrical panels, modules, and assemblies used in each model produced with

If Vertical or Horizontal sweep should fail, D502 or D503 will conduct turning transistor Q501 On. This will turn Q500 Off, which will turn Q503 Off,

Troubleshooting the High Voltage Power Supply Loss of High Voltage can be caused by a failure in the drive circuits, beam current shutdown, overvolta

Audio Switching Baseband Audio from Tuner 1 and Tuner 2 are fed to IC105, the Audio Switch, on Pins 2, 1, 13, and 12. (Figure 8) Switching for IC105

AUDIO POWER SUPPLY A switch mode power supply on the Audio amplifier board supplies the 43 and 12 volt sources to power the output. IC401 provides

AUDIO OUTPUT (Figure 10) To prevent a Pop in the speakers when the set is turned on, Q203, Q204, Q207, and Q208 provide muting. When the Audio P

SPEAKER OUTPUT CIRCUIT (Figure 11) In the PTV810 and above, the Right and Left internal Speakers are connected to J254A on the Audio Amplifier pa

Troubleshooting the Audio Circuit To troubleshoot a no audio problem, first measure J278, Pins 1 and 2, for audio drive. If this signal is present,

Convergence Panel Phase-Locked Loop: The phase-locked loop produces a 13.59mhz signal, which is phase locked to the 15,734 Hz horizontal blanking pu

corrections signals for red, green, and blue horizontal and vertical. The dac outputs are approximately 2 volts peak to peak with a 2.5 volt dc offse

Small Signal Panel Chassis PTV810 and above are equipped with a dual tuner PIP. (Figure 13) Composite Video output from each Tuner circuit is fed to

PTV805 8P4831C101 48" Philips/Magnavox 8P4834C101 48" Philips/Magnavox 8P5431C101 54" Philips/Magnavox 8P5434C101 54" Philips/

Tuner Each tuner has it's own Saw Filter and IF circuitry. (Figure 14) The output from the Tuner on Pins 16 and 17 is fed to the input of Saw

Video Switcher The Video output of each tuner and IF is buffered and fed to the Audio/Video switcher IC1 on Pins 33 and 47. (Figure 15) Either of the

Signal Processor Luminance from IC701 is fed through a delay circuit, amplified by Q601, and is buffered by Q611 and applied to IC600 Pin 61. (Figure

BOARD LEVEL TROUBLESHOOTING For a dead set condition, check the 5 volt standby supply on J403 Pin 1 of the Small Signal Panel or J403 Pin 7 of the La

PTV800(7573) 12 Vp-p20 usec 25.1 Vp-p20 usec 35 Vp-p5 msec 41.7 Vp-p20 usec 50.8 Vp-p20 usec 63.5 Vp-p20 usec 74.6 Vp-p20 usec 810 Vp-p5 msec 94 Vp-p2

PTV800(7573)211.1 Vp-p20 usec220.8 Vp-p20 usec232 Vp-p20 usec 113 Vp-p5 usec 3A1280 Vp-p5 usec 3B220 Vp-p5 usec 3C310 Vp-p5 usec 42 Vp-p5 msec 52.8 Vp

PTV800(7573)14C375 Vp-p20 usec14D112 Vp-p20 usec14B7 Vp-p20 usec15A25 Vp-p20 usec15B250 Vp-p20 usec16A6.2 Vp-p5 msec16B6.2 Vp-p5 msec175 Vp-p20 usec18

PTV800(7573) 62.3 Vp-p5 msec 71 Vp-p5 msec 82 Vp-p5 msec 91 Vp-p5 msec102.4 Vp-p5 msec11700 mVp-p5 msec121.5 Vp-p5 msec131.6 Vp-p20 usec141.6 Vp-p20 u

PTV800(7573) 9450 mVp-p5 msec10440 mVp-p20 usec11450 mVp-p20 usec123 Vp-p20 usec134.5 Vp-p20 usec143 Vp-p20 usec15640 mVp-p20 usec1644 Vp-p5 msec173.2

PTV800(7573)291.8 Vp-p20 usec301.75 Vp-p20 usec311.75 Vp-p20 usec32A1.2 Vp-p20 usec32B1.7 Vp-p20 usec331.2 Vp-p0.1usec34A0.8 Vp-p20 usec34C1.4 Vp-p20

PTV811 48PP72A001 48" Philips Brazil 48XP43C101 48" Philips Taiwan/Latam 48XP44C101 48" Philips Korea 54PP72A001 54" Philips B

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - PTV 800 & 805 WIRING DIAGRAM

USED ONLY IN MODELS: 8P4841C, 8P4844C, 8P5441C, 8P5444C, 8P6041C, 8P6044C, 8P6051C, 8P6054 (7573) - PTV 810 & 811 WIRING DIAGRAM

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - PTV 815, 820 & 825 WIRING DIAGRAM

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 1

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 2

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 3

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 4

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 5

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - SECTION 6

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

PTV815 MX5472C101 54" Magnavox MX6072C101 60" Magnavox MX6472C101 64" Magnavox Reference Description 00APD020A001 Large Signal P

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - SE

All Models (7573) - LARGE SIGNAL PANEL - APD019, APD020 & APD021- SECTION 1 SCHEMATIC

All Models (7573) - LARGE SIGNAL PANEL - APD019, APD020 & APD021- SECTION 2 SCHEMATIC

All Models (7573) - LARGE SIGNAL PANEL - APD019, APD020 & APD021- SECTION 3 SCHEMATIC

All Models (7573) - DIGITAL CONVERGENCE PANEL - A10688 - SECTION 1 SCHEMATIC

PTV825 PV5470C104/105 54" Marantz PV6070C104/105 60" Marantz Reference Description 00APD020A001 Large Signal Panel 00ASG054A001 Small

All Models (7573) - DIGITAL CONVERGENCE PANEL - A10688 - SECTION 2 SCHEMATIC

All Models (7573) - DIGITAL CONVERGENCE PANEL - A10688 - SECTION 3 SCHEMATIC

All Models (7573) - RED CRT PANEL SCHEMATIC

All Models (7573) - GREEN CRT PANEL SCHEMATIC

All Models (7573) - BLUE CRT PANEL SCHEMATIC

USED ONLY IN MODELS: 48PP72A, 48XP43C, 48XP44, 54PP72, 54XP43, 54XP44, 60XP43, MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - 25 WATT AMP

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - WALLVISION SWITCH PANEL SCHEMATIC

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C, PV5470, PV6070, XV5270 (7573) - SVM SCHEMATIC

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - STEREO SPREAD MODULE SCHEMATIC

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - GUIDE PLUS SCHEMATIC

SMALL SIGNAL PANEL SCHEMATIC & WAVEFORM NOTES: CAUTION: A SEPARATE ISOLATION TRANSFORMER MUST BE USED WHEN SERVICING THIS CHASSIS. SMALL SIGNAL

All Models (7573) - IR RECEIVER ASSEMBLY SCHEMATIC

All Models (7573) - SWITCH PANEL SCHEMATIC

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, PV5470, PV6070 (7573) - REMOTE LOCATOR SCHEMATIC

USED ONLY IN MODELS: 48PP72A, 48XP43C, 48XP44, 54PP72, 54XP43, 54XP44, 60XP43, MX5472C, MX6072C, MX6472C, PV5470, PV6070 (7573) - FRONT JACK PANEL SC

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - CBA (TOP

USED ONLY IN MODELS: 1152980001, , 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG051 & ASG052 - CBA (BOTT

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - CB

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C (7573) - SMALL SIGNAL PANEL - ASG053, ASG054 & ASG056 - CB

All Models (7573) - LARGE SIGNAL PANEL CBA (TOP VIEW)

All Models (7573) - LARGE SIGNAL PANEL CBA (BOTTOM VIEW)

LARGE SIGNAL PANEL SCHEMATIC AND WAVEFORM NOTES: 1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN WITH AN NTSC COLOR BAR PATTERN SIGNAL APPLIED. 2. SWEEP

All Models (7573) - DIGITAL CONVERGENCE PANEL - CBA (TOP VIEW)

All Models (7573) - DIGITAL CONVERGENCE PANEL - CBA (BOTTOM VIEW)

All Models (7573) - RED CRT PANEL CBA (TOP VIEW)

All Models (7573) - RED CRT PANEL CBA (BOTTOM VIEW)

All Models (7573) - GREEN CRT PANEL CBA (TOP VIEW)

All Models (7573) - GREEN CRT PANEL CBA (BOTTOM VIEW)

All Models (7573) - BLUE CRT PANEL CBA (TOP VIEW)

All Models (7573) - BLUE CRT PANEL CBA (BOTTOM VIEW)

USED ONLY IN MODELS: 48PP72A, 48XP43C, 48XP44, 54PP72, 54XP43, 54XP44, 60XP43, MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - 25 WATT AMP

USED ONLY IN MODELS: 48PP72A, 48XP43C, 48XP44, 54PP72, 54XP43, 54XP44, 60XP43, MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - 25 WATT AMP

DIGITAL CONVERGENCE PANEL SCHEMATIC AND WAVEFORM NOTES: UNLESS OTHERWISE SPECIFIED: 1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN WITH AN NTSC COLOR BAR

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - WALLVISION SWITCH PANEL CBA (TOP VIEW)

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - WALLVISION SWITCH PANEL CBA (BOTTOM VIEW)

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C, PV5470, PV6070, XV5270 (7573) - SVM CBA (TOP VIEW)

NOT USED IN MODELS: , 1152980001, 8P4831C, 8P4834C, 8P5431C, 8P5434C, 8P6031C, 8P6034C, PV5470, PV6070, XV5270 (7573) - SVM CBA (BOTTOM VIEW)

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - STEREO SPREAD MODULE CBA (TOP VIEW)

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - STEREO SPREAD MODULE CBA (BOTTOM VIEW)

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - GUIDE PLUS CBA (TOP VIEW)

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, XV5270, PV5470, PV6070 (7573) - GUIDE PLUS CBA (BOTTOM VIEW)

All Models (7573) - IR RECEIVER ASSEMBLY CBA

All Models (7573) - SWITCH PANEL CBA

Cabinet Replacement Parts Lists Cabinet Exploded View

USED ONLY IN MODELS: MX5472C, MX6072C, MX6472C, PV5470, PV6070 (7573) - REMOTE LOCATOR CBA

USED ONLY IN MODELS: 48PP72A, 48XP43C, 48XP44, 54PP72, 54XP43, 54XP44, 60XP43, MX5472C, MX6072C, MX6472C, PV5470, PV6070 (7573) - FRONT JACK PANEL CB

CABINET EXPLODED VIEW

CRT LENS ASSEMBLY EXPLODED VIEW

1152980001 - Manual no. 7573 CBA's CBA&apos

1152980001 (continued) R106 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R107

1152980001 (continued) Q207 Transistor, PNP, SJE1763 . . . . . . . 4835 130 47084 Q250

1152980001 (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

1152980001 (continued) C220 0.1uF., 10%, 50V, Ceramic. . . . . . . 4835 122 87061 C221

1152980001 (continued) R199 100k, 5%, 1/2W, Metal Film . . . . . . 4835 116 57687 R200

IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Philips Consumer Electronics Company** Equipment

001152980001 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

1152980001 (continued) R674 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R675

1152980001 (continued) L302 Peaking Coil, 12uH., 5%. . . . . . . . 4835 150 57058 L303

1152980001 (continued) S C916 6800pF., 10%, 50V, Polyester . . . . . 2020 300 90571 C917

1152980001 (continued) R943 2.2k, Control Adjust . . . . . . . . . 4835 100 17047S R944

1152980001 (continued) J511 Contact Pin. . . . . . . . . . . . . . 3135 010 00470 J540

48PP72A - Manual no. 7573 CBA's CBA&apos

48PP72A (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

48PP72A (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

48PP72A (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

48PP72A (continued) 27 Back Cover (Lower) . . . . . . . . . . 3135 013 01290 26

0048PP72A001 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

48PP72A (continued) C322 1uF., 20%, 50V, Electrolytic . . . . . 3198 025 51080 C323

48PP72A (continued) R34 2.2k, 5%, 1/2W, Metal Film . . . . . . 4835 110 47006S R35

48PP72A (continued) R329 470 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57723 R330

48PP72A (continued) R780 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R783

48PP72A (continued) L201 Adjustable LC Coil, 4.5M . . . . . . . 4835 157 57113 L202

48PP72A (continued) C558 150pF., 10%, 500V, Ceramic . . . . . . 2020 557 90711 C559

48PP72A (continued) R823 68k, 5%, 1/4W, Metal Film. . . . . . . 4835 111 37118 R824

48PP72A (continued) L550 Suppression Coil, 10uH.. . . . . . . . 4835 152 27002 L803

48PP72A (continued) P Coupler, Green . . . . . . . . . . . . 4835 290 87152 R

48XP43C - Manual no. 7573 CBA's CBA&apos

0048XP43C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

48XP43C (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

48XP43C (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

48XP43C (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

48XP43C (continued) 27 Back Cover (Lower) . . . . . . . . . . 4835 432 97717 26

48XP43C (continued) C314 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C315

48XP43C (continued) R26 180k, 5%, 1/10W, Carbon Film . . . . . 4835 111 37484 R28

48XP43C (continued) R322 1k, 5%, 1/2W, Metal Film . . . . . . . 4835 116 57685 R323

48XP43C (continued) R773 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R774

48XP43C (continued) Z11 Zener Diode, BZX284-C3V3 . . . . . . . 9340 385 60115 Z12

48XP43C (continued) C483 100uF., 25V, Electrolytic. . . . . . . 4835 124 47501 C499

0048XP44C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135 010 03060

48XP43C (continued) S R813 1.5 ohm, 5%, 2W, Metal Film. . . . . . 4835 116 67217 R814

48XP43C (continued) L427 Ferrite Bead . . . . . . . . . . . . . 4835 526 17001 L428

48XP43C (continued) I Coolant (Enough to do 3 CRTs). . . . . 3135 010 02040 K

48XP44 - Manual no. 7573 CBA's CBA&apos

48XP44 (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

48XP44 (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

48XP44 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

48XP44 (continued) 27 Back Cover (Lower) . . . . . . . . . . 4835 432 97717 26

48XP44 (continued) C318 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C319

48XP44 (continued) R31 2.2k, 5%, 1/2W, Metal Film . . . . . . 4835 110 47006 R32

0054PP72A001 "s" in the "s" column indicates a safety part. Ref. Ref No Part Number Description AC/CORD 20 s 4835 321 17128

48XP44 (continued) R326 1k, 5%, 1/4W, Carbon Film. . . . . . . 4835 111 37022 R327

48XP44 (continued) R777 10k, 5%, 1/10W, Carbon Film. . . . . . 4835 111 37216 R778

48XP44 (continued) Z201 Zener Diode, MMSZ5257B . . . . . . . . 4835 130 37823 Z300

48XP44 (continued) C511 0.1uF., 10%, 50V, Polyester. . . . . . 4822 121 42094 C555

48XP44 (continued) S R817 470 ohm, 5%, 1/4W, Metal Film. . . . . 4835 111 37104 R821

48XP44 (continued) L432 Suppression Coil, 10uH.. . . . . . . . 4835 152 27002 L435

48XP44 (continued) O Expansion Diaphragm. . . . . . . . . . 3135 013 01060 P

54PP72 - Manual no. 7573 CBA's CBA&apos

54PP72 (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

54PP72 (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

0054XP43C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835

54PP72 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

54PP72 (continued) 27 Back Cover (Lower) . . . . . . . . . . 3135 013 01300 26

54PP72 (continued) C322 1uF., 20%, 50V, Electrolytic . . . . . 3198 025 51080 C323

54PP72 (continued) R34 2.2k, 5%, 1/2W, Metal Film . . . . . . 4835 110 47006S R35

54PP72 (continued) R329 470 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57723 R330

54PP72 (continued) R780 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R783

54PP72 (continued) L201 Adjustable LC Coil, 4.5M . . . . . . . 4835 157 57113 L202

54PP72 (continued) C558 150pF., 10%, 500V, Ceramic . . . . . . 2020 557 90711 C559

54PP72 (continued) R823 68k, 5%, 1/4W, Metal Film. . . . . . . 4835 111 37118 R824

54PP72 (continued) L550 Suppression Coil, 10uH.. . . . . . . . 4835 152 27002 L803

0054XP44C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135 010 03060

54PP72 (continued) P Coupler, Green . . . . . . . . . . . . 4835 290 87152 R

54XP43 - Manual no. 7573 CBA's CBA&apos

54XP43 (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

54XP43 (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

54XP43 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

54XP43 (continued) Back Cover CRT . . . . . . . . . . . . 3135 013 02360

54XP43 (continued) C313 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C314

54XP43 (continued) R25 180k, 5%, 1/10W, Carbon Film . . . . . 4835 111 37484 R26

54XP43 (continued) R321 4.7k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27052 R322

54XP43 (continued) R772 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R773

005545380002 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835

54XP43 (continued) Z10 Zener Diode, BZX284-C3V3 . . . . . . . 9340 385 60115 Z11

54XP43 (continued) C482 0.1uF., 50V, Ceramic . . . . . . . . . 4835 122 87375 C483

54XP43 (continued) R812 68k, 5%, 1/4W, Metal Film. . . . . . . 4835 111 37118S R813

54XP43 (continued) L426 Suppression Coil, 42uH.. . . . . . . . 4835 157 57063 L427

54XP43 (continued) H Seal, CRT. . . . . . . . . . . . . . . 3135 013 02321 I

54XP44 - Manual no. 7573 CBA's CBA&apos

54XP44 (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

54XP44 (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

54XP44 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

54XP44 (continued) 26 Back Cover (Upper) . . . . . . . . . . 4835 432 97693

0060XP43C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135

54XP44 (continued) C317 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C318

54XP44 (continued) R30 75 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37276 R31

54XP44 (continued) R325 1k, 5%, 1/2W, Metal Film . . . . . . . 4835 116 57685 R326

54XP44 (continued) R776 5.1k, 2%, 1/8W, Carbon Film. . . . . . 2322 730 31512 R777

54XP44 (continued) Z200 Zener Diode, MMSZ5257B . . . . . . . . 4835 130 37823 Z201

54XP44 (continued) C503 680pF., 5%, 50V, Ceramic . . . . . . . 4835 122 87037 C511

54XP44 (continued) S R816 0.56 ohm, 5%, 1/2W, Metal Film . . . . 4835 116 67006S R817

54XP44 (continued) L430 Ferrite Bead . . . . . . . . . . . . . 4835 526 17001 L432

54XP44 (continued) M Diaphragm Cover. . . . . . . . . . . . 4835 432 17736 O

60XP43 - Manual no. 7573 CBA's CBA&apos

008P4831C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

60XP43 (continued) C110 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C111

60XP43 (continued) R258 150 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 57151 R259

60XP43 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

60XP43 (continued) 27 Back Cover (Lower) . . . . . . . . . . 3135 013 02350 26

60XP43 (continued) C315 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C316

60XP43 (continued) R28 75 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37276 R29

60XP43 (continued) R323 4.7k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27052 R324

60XP43 (continued) R774 470 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57723 R775

60XP43 (continued) Z12 Zener Diode, BZX284-C3V3 . . . . . . . 9340 385 60115 Z100

60XP43 (continued) C499 0.1uF., 10%, 50V, Ceramic. . . . . . . 4835 122 87061 C501

FIRE AND SHOCK HAZARD 1. Be sure all components are positioned in such a way as to avoid the possibility of adjacent component shorts. This is especia

008P4834C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

60XP43 (continued) R814 33 ohm, 5%, 1/2W, Metal Film . . . . . 4835 116 57366 R815

60XP43 (continued) L428 Suppression Coil, 42uH.. . . . . . . . 4835 157 57063 L429

60XP43 (continued) K Fill Plug. . . . . . . . . . . . . . . 4835 432 17791 L

8P4831C - Manual no. 7573 CBA's CBA&apos

8P4831C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P4831C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P4831C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P4831C (continued) C212 0.068uF., 10%, 50V, Ceramic. . . . . . 4835 122 87448 C213

8P4831C (continued) R4 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R5

8P4831C (continued) R353 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R354

008P4841C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P4831C (continued) R1030 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R1032

8P4831C (continued) J5 4 Pin Push Terminal. . . . . . . . . . 4835 265 97448 J250

8P4831C (continued) S R408 0.12 ohm, 5%, 1W, Metal Film . . . . . 4835 116 67121S R409

8P4831C (continued) R2835 3k, 5%, 1/2W, Metal Film . . . . . . . 4835 116 57757 R2836

8P4831C (continued) 00ASW129, 00ASW130 & 00ASW131 SWITCH ASSEMBLY 00ASW129, 0

8P4834C - Manual no. 7573 CBA's CBA&apos

8P4834C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P4834C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P4834C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P4834C (continued) C210 16pF., 5%, 50V, Ceramic. . . . . . . . 4835 122 87449 C211

008P4844C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P4834C (continued) BRXXX 0 ohm, "Chip" Jumper . . . . . . . . . 4835 111 270

8P4834C (continued) R351 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R352

8P4834C (continued) R1023 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R1027

8P4834C (continued) J2 Phono Jack Assembly. . . . . . . . . . 4835 265 97388 J3

8P4834C (continued) R406 100 ohm, 5%, 1/4W, Carbon. . . . . . . 4835 110 57247S R407

8P4834C (continued) R2812 110k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37052 R2834

8P4834C (continued) J302 5 Pin Board Connector. . . . . . . . . 2422 038 00176 J305

8P4841C - Manual no. 7573 CBA's CBA&apos

8P4841C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P4841C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

008P5431C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P4841C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P4841C (continued) Front Jack Panel . . . . . . . . . . . 4835 219 77787 9

8P4841C (continued) C363 100pF., 5%, 50V, Ceramic . . . . . . . 3198 016 01010 C375

8P4841C (continued) R49 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R51

8P4841C (continued) R338 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R339

8P4841C (continued) R798 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R799

8P4841C (continued) L211 Peaking Coil, 12uH., 5%. . . . . . . . 4835 150 57058 L212

8P4841C (continued) C571 0.1uF., 50V, Ceramic . . . . . . . . . 4835 122 87375 C572

8P4841C (continued) R829 15 ohm, 1/2W, Metal Film . . . . . . . 4835 116 57699S R830

8P4841C (continued) L902 Coil, 22uH., 10% . . . . . . . . . . . 4835 150 57052 L903

008P5434C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P4844C - Manual no. 7573 CBA's CBA&apos

8P4844C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P4844C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

8P4844C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P4844C (continued) 4 Foot Base Rail (x2). . . . . . . . . . 3135 014 03131

8P4844C (continued) C362 100pF., 5%, 50V, Ceramic . . . . . . . 3198 016 01010 C363

8P4844C (continued) R48 75 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37276 R49

8P4844C (continued) R337 47k, 5%, 1/2W, Metal Film. . . . . . . 4835 116 57725 R338

8P4844C (continued) R791 6.8k, 5%, 1/2W, Metal Film . . . . . . 4835 116 57736 R798

8P4844C (continued) L210 Peaking Coil, 47uH., 5%. . . . . . . . 4835 150 57055 L211

008P5441C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P4844C (continued) C570 0.1uF., 50V, Ceramic . . . . . . . . . 4835 122 87375 C571

8P4844C (continued) R828 68k, 5%, 1/4W, Metal Film. . . . . . . 4835 111 37118 R829

8P4844C (continued) L805 Ferrite Bead . . . . . . . . . . . . . 4835 526 17003 L902

8P5431C - Manual no. 7573 CBA's CBA&apos

8P5431C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P5431C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P5431C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P5431C (continued) C211 0.47uF., 35V, Electrolytic . . . . . . 4835 124 97182 C212

8P5431C (continued) S R3 22 ohm, 5%, 1/2W, Metal Film . . . . . 4835 116 57708 R4

8P5431C (continued) R352 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R353

008P5444C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P5431C (continued) R1027 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R1030

8P5431C (continued) J3 Jack Assembly. . . . . . . . . . . . . 4835 265 97386 J5

8P5431C (continued) S R407 0.1 ohm, 5%, 1W, Metal Film. . . . . . 4835 116 67179S R408

8P5431C (continued) R2834 0.27 ohm, 5%, 1/2W, Metal Film . . . . 4835 116 57112 R2835

8P5431C (continued) J305 3 Pin Board Connector. . . . . . . . . 2422 038 0017500ASW129

8P5434C - Manual no. 7573 CBA's CBA&apos

8P5434C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P5434C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P5434C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P5434C (continued) C210 16pF., 5%, 50V, Ceramic. . . . . . . . 4835 122 87449 C211

008P6031C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P5434C (continued) BRXXX 0 ohm, "Chip" Jumper . . . . . . . . . 4835 111 270

8P5434C (continued) R351 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R352

8P5434C (continued) R1023 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R1027

8P5434C (continued) J2 Phono Jack Assembly. . . . . . . . . . 4835 265 97388 J3

8P5434C (continued) R406 100 ohm, 5%, 1/4W, Carbon. . . . . . . 4835 110 57247S R407

8P5434C (continued) R2812 110k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37052 R2834

8P5434C (continued) J302 5 Pin Board Connector. . . . . . . . . 2422 038 00176 J305

8P5441C - Manual no. 7573 CBA's CBA&apos

8P5441C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P5441C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

008P6034C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P5441C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P5441C (continued) Front Jack Panel . . . . . . . . . . . 4835 219 77787 9

8P5441C (continued) C363 100pF., 5%, 50V, Ceramic . . . . . . . 3198 016 01010 C375

8P5441C (continued) R49 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R51

8P5441C (continued) R338 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R339

8P5441C (continued) R798 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R799

8P5441C (continued) L211 Peaking Coil, 12uH., 5%. . . . . . . . 4835 150 57058 L212

8P5441C (continued) C571 0.1uF., 50V, Ceramic . . . . . . . . . 4835 122 87375 C572

8P5441C (continued) R829 15 ohm, 1/2W, Metal Film . . . . . . . 4835 116 57699S R830

8P5441C (continued) L902 Coil, 22uH., 10% . . . . . . . . . . . 4835 150 57052 L903

008P6041C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P5444C - Manual no. 7573 CBA's CBA&apos

8P5444C (continued) R105 1.2k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27042 R106

8P5444C (continued) Q206 Transistor, NPN, SJE1331-5 . . . . . . 4835 130 47107 Q207

8P5444C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P5444C (continued) C210 16pF., 5%, 50V, Ceramic. . . . . . . . 4835 122 87449 C211

8P5444C (continued) C1005 100pF., 5%, 50V, Ceramic . . . . . . . 3198 016 01010 C1006

8P5444C (continued) R269 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R271

8P5444C (continued) R708 10k, 5%, 1/10W, Carbon Film. . . . . . 4835 111 37216 R709

8P5444C (continued) Q600 Transistor BC847B. . . . . . . . . . . 4822 130 60511 Q601

8P5444C (continued) S C424 470uF., 250V, Electrolytic . . . . . . 4835 124 47141 C425

LEAKAGE CURRENT COLD CHECK 1. Unplug the ac line cord and connect a jumper between the two prongs of the plug. 2. Turn on the power switch. 3. Meas

008P6044C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P5444C (continued) R486 1k, 5%, 1/4W, Carbon Film. . . . . . . 4835 110 57018 R500

8P5444C (continued) IC552 IC MC7812CT, 12V Regulator . . . . . . 4835 209 88554 IC900

8P6031C - Manual no. 7573 CBA's CBA&apos

8P6031C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P6031C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P6031C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P6031C (continued) C209 0.01uF., 10%, 50V, Ceramic . . . . . . 4835 122 87042 C210

8P6031C (continued) BRXXX 0 ohm, Jumper. . . . . . . . . . . . . 3198 021 90010 BRXXX

8P6031C (continued) R350 4.7k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27052 R351

8P6031C (continued) R1022 22k, 5%, 1/2W, Metal Film. . . . . . . 4835 116 57706 R1023

008P6051C101 "s" in the "s" column indicates a safety part. Ref. Ref s Part Number Description AC/CORD 20 s 4835 321 17128 A

8P6031C (continued) HS703 Heatsink for IC 703. . . . . . . . . . 3135 011 02510 J2

8P6031C (continued) S R405 4.7 ohm, 1/2W, Metal Film. . . . . . . 4835 116 57009 R406

8P6031C (continued) R2810 1.1k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37051 R2812

8P6031C (continued) IR300 IR Receiver. . . . . . . . . . . . . . 4835 219 67061 J302

8P6034C - Manual no. 7573 CBA's CBA&apos

8P6034C (continued) R107 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R108

8P6034C (continued) Q250 Transistor, NPN, BC547B. . . . . . . . 4835 130 47055 Q251

8P6034C (continued) J654A 10 Pin Board Connector . . . . . . . . 2422 025 15027 J658A

8P6034C (continued) C208 330pF., 10%, 50V, Ceramic. . . . . . . 4835 122 47047 C209

8P6034C (continued) BRSXXX 0 ohm, "Chip" Jumper . . . . . . . . . 4835 111 270

00MX5472C101 "s" in the "s" column indicates a safety part. Ref. Ref s Part Number Description AC/CORD 20 s 4835 321 17128

8P6034C (continued) R348 470 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57723 R350

8P6034C (continued) R1021 22k, 5%, 1/2W, Metal Film. . . . . . . 4835 116 57706 R1022

8P6034C (continued) HS401 Heatsink for IC 401. . . . . . . . . . 3135 011 03291 HS703

8P6034C (continued) S R404 100 ohm, 5%, 10W, Wire Wound . . . . . 4835 112 37032S R405

8P6034C (continued) S R980 4.7k, 5%, 10W, Metal Oxide . . . . . . 4835 116 67272 R2810

8P6034C (continued) D302 Red LED. . . . . . . . . . . . . . . . 4835 130 97096 IR300

8P6041C - Manual no. 7573 CBA's CBA&apos

8P6041C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P6041C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

8P6041C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

00MX6072C101 "s" in the "s" column indicates a safety part. Ref. Ref s Part Number Description AC/CORD 20 s 4835 321 17128

8P6041C (continued) Frame, Screen Top 60 (x2). . . . . . . 3135 014 03410

8P6041C (continued) C360 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C362

8P6041C (continued) R46 390 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37253 R48

8P6041C (continued) R336 4.7k, 5%, 1/2W, Metal Film . . . . . . 4835 116 57724 R337

8P6041C (continued) R790 10k, 5%, 1/10W, Carbon Film. . . . . . 4835 111 37216 R791

8P6041C (continued) L209 Peaking Coil, 1000uH., . . . . . . . . 4835 157 57828 L210

8P6041C (continued) C569 0.1uF., 50V, Ceramic . . . . . . . . . 4835 122 87375 C570

8P6041C (continued) R827 68k, 5%, 1/4W, Metal Film. . . . . . . 4835 111 37118 R828

8P6041C (continued) L804 Linear Coil. . . . . . . . . . . . . . 0036 202 80026 L805

8P6044C - Manual no. 7573 CBA's CBA&apos

00MX6472C101 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 4835 321 17128

8P6044C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P6044C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

8P6044C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P6044C (continued) Baffle Mount Receptacle (x6) . . . . . 4835 265 97154

8P6044C (continued) C318 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C319

8P6044C (continued) R31 2.2k, 5%, 1/2W, Metal Film . . . . . . 4835 110 47006 R32

8P6044C (continued) R326 1k, 5%, 1/4W, Carbon Film. . . . . . . 4835 111 37022 R327

8P6044C (continued) R777 10k, 5%, 1/10W, Carbon Film. . . . . . 4835 111 37216 R778

8P6044C (continued) Z201 Zener Diode, MMSZ5257B . . . . . . . . 4835 130 37823 Z300

8P6044C (continued) C511 0.1uF., 10%, 50V, Polyester. . . . . . 4822 121 42094 C555

00PV5470 C104, C105 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135 010

8P6044C (continued) R814 33 ohm, 5%, 1/2W, Metal Film . . . . . 4835 116 57366 R815

8P6044C (continued) L426 Suppression Coil, 42uH.. . . . . . . . 4835 157 57063 L427

8P6044C (continued) H Seal, CRT. . . . . . . . . . . . . . . 3135 013 02321 I

8P6051C - Manual no. 7573 CBA's CBA&apos

8P6051C (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P6051C (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

8P6051C (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P6051C (continued) Back Cover Ctr.. . . . . . . . . . . . 4835 432 97697

8P6051C (continued) C310 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C311

8P6051C (continued) R20 180k, 5%, 1/10W, Carbon Film . . . . . 4835 111 37484 R21

00PV6070 C104, C105 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135 01

8P6051C (continued) R318 1k, 5%, 1/2W, Metal Film . . . . . . . 4835 116 57685 R319

8P6051C (continued) R761 1k, 5%, 1/4W, Carbon Film. . . . . . . 4835 111 37022 R762

8P6051C (continued) Z7 Zener Diode, BZX284-C3V3 . . . . . . . 9340 385 60115 Z8

8P6051C (continued) C479 1000uF., 50V, Electrolytic . . . . . . 4835 124 47573 C480

8P6051C (continued) R806 1k, 20%, 1/2W, Carbon Comp.. . . . . . 4835 110 47215 R807

8P6051C (continued) L415 Suppression Coil, 1.8uH. . . . . . . . 4835 152 27029 L416

8P6051C (continued) Focus Lead . . . . . . . . . . . . . . 3135 010 00730S

8P6054 - Manual no. 7573 CBA's CBA&apos

8P6054 (continued) C112 270pF., 10%, 50V, Ceramic Disc . . . . 4835 122 47668 C127

8P6054 (continued) R260 18k, 5%, 1/2W, Metal Film. . . . . . . 4835 110 57187 R261

00XV5270B103 "s" in the "s" column indicates a safety part. Ref. Ref No s Part Number Description AC/CORD 20 s 3135 010 03060

8P6054 (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

8P6054 (continued) Back Cover Ctr.. . . . . . . . . . . . 4835 432 97697

8P6054 (continued) C310 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C311

8P6054 (continued) R20 180k, 5%, 1/10W, Carbon Film . . . . . 4835 111 37484 R21

8P6054 (continued) R318 1k, 5%, 1/2W, Metal Film . . . . . . . 4835 116 57685 R319

8P6054 (continued) R761 1k, 5%, 1/4W, Carbon Film. . . . . . . 4835 111 37022 R762

8P6054 (continued) Z7 Zener Diode, BZX284-C3V3 . . . . . . . 9340 385 60115 Z8

8P6054 (continued) C479 1000uF., 50V, Electrolytic . . . . . . 4835 124 47573 C480

8P6054 (continued) R806 1k, 20%, 1/2W, Carbon Comp.. . . . . . 4835 110 47215 R807

8P6054 (continued) L415 Suppression Coil, 1.8uH. . . . . . . . 4835 152 27029 L416

00706086 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

8P6054 (continued) Focus Lead . . . . . . . . . . . . . . 3135 010 00730S

MX5472C - Manual no. 7573 CBA's CBA&apos

MX5472C (continued) C108 2.2uF., 20%, 50V, Electrolytic . . . . 3198 025 52280 C109

MX5472C (continued) R256 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R257

MX5472C (continued) F2 4 Amp Fuse . . . . . . . . . . . . . . 4835 253 37027 F3

MX5472C (continued) C15 0.1uF., 20%, 50V, Ceramic. . . . . . . 2238 581 16741 R3

MX5472C (continued) C233 10uF., 20V, Electrolytic . . . . . . . 4835 124 97184 C234

MX5472C (continued) C1029 1uF., 20%, 50V, Electrolytic . . . . . 3198 025 51080 C1031

MX5472C (continued) R288 4.7k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27052 R289

MX5472C (continued) R721 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R722

00706087 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

MX5472C (continued) Q614 Transistor BC847B. . . . . . . . . . . 4822 130 60511 Q616

MX5472C (continued) C440 220pF., 10%, 1kV, Ceramic. . . . . . . 4835 122 47458 C441

MX5472C (continued) R514 10k, 5%, 1/8W, Metal Film. . . . . . . 4835 111 37556 R550

MX5472C (continued) Q501 Transistor, BC85 H&V Dfl Fail-safe . . 5322 130 60508 Q5

MX5472C (continued) S R779 330 ohm, 5%, 5W, Wire Wnd. . . . . . . 4835 112 27043 R782

MX5472C (continued) R50 4.7k, 5%, 1/10W, Metal Film. . . . . . 4835 111 37444 R51

MX6072C - Manual no. 7573 CBA's CBA&apos

MX6072C (continued) C108 2.2uF., 20%, 50V, Electrolytic . . . . 3198 025 52280 C109

MX6072C (continued) R256 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R257

MX6072C (continued) F2 4 Amp Fuse . . . . . . . . . . . . . . 4835 253 37027 F3

00706088 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

MX6072C (continued) C15 0.1uF., 20%, 50V, Ceramic. . . . . . . 2238 581 16741 R3

MX6072C (continued) C233 10uF., 20V, Electrolytic . . . . . . . 4835 124 97184 C234

MX6072C (continued) C1029 1uF., 20%, 50V, Electrolytic . . . . . 3198 025 51080 C1031

MX6072C (continued) R288 4.7k, 5%, 1/10W, Carbon Film . . . . . 4835 111 27052 R289

MX6072C (continued) R721 1k, 5%, 1/10W, Carbon Film . . . . . . 4822 051 10102 R722

MX6072C (continued) Q614 Transistor BC847B. . . . . . . . . . . 4822 130 60511 Q616

MX6072C (continued) C440 220pF., 10%, 1kV, Ceramic. . . . . . . 4835 122 47458 C441

MX6072C (continued) R514 10k, 5%, 1/8W, Metal Film. . . . . . . 4835 111 37556 R550

MX6072C (continued) Q501 Transistor, BC85 H&V Dfl Fail-safe . . 5322 130 60508 Q5

MX6072C (continued) S R779 330 ohm, 5%, 5W, Wire Wnd. . . . . . . 4835 112 27043 R782

00706089 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

MX6072C (continued) R50 4.7k, 5%, 1/10W, Metal Film. . . . . . 4835 111 37444 R51

MX6472C - Manual no. 7573 CBA's CBA&apos

MX6472C (continued) C108 2.2uF., 20%, 50V, Electrolytic . . . . 3198 025 52280 C109

MX6472C (continued) R256 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R257

MX6472C (continued) F2 4 Amp Fuse . . . . . . . . . . . . . . 4835 253 37027 F3

MX6472C (continued) C15 0.1uF., 20%, 50V, Ceramic. . . . . . . 2238 581 16741 R3

MX6472C (continued) C234 0.1uF., 20%, 50V, Ceramic. . . . . . . 2238 581 16741 C235

MX6472C (continued) C1031 1uF., 35V Electrolytic . . . . . . . . 4835 124 97175 C1033

MX6472C (continued) R289 3.6k, 5%, 1/10W, Carbon Film . . . . . 3198 021 53620 R291

MX6472C (continued) R722 560 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 27054 R723

00706092 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

MX6472C (continued) Q616 Transistor BC85. . . . . . . . . . . . 5322 130 60508 Q617

MX6472C (continued) C441 6800uF., 16V, Electrolytic . . . . . . 4835 124 47579 C442

MX6472C (continued) R550 47k, 5%, 1/10W, Metal Film . . . . . . 4835 111 37445 R554

MX6472C (continued) Q502 Transistor, BC847B . . . . . . . . . . 4822 130 60511 Q503

MX6472C (continued) R782 330 ohm, 1/2W, Metal Film. . . . . . . 4835 116 57713 R783

MX6472C (continued) R51 4.7k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37037 R52

PV5470 - Manual no. 7573 CBA's CBA&apos

PV5470 (continued) C109 2.2uF., 20%, 50V, Electrolytic . . . . 3198 025 52280 C110

PV5470 (continued) R257 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R258

PV5470 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

00706101 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

PV5470 (continued) R4 68 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37408 R5

PV5470 (continued) C375 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C377

PV5470 (continued) R52 47k, 5%, 1/10W, Metal Film . . . . . . 4835 111 37445 R53

PV5470 (continued) R340 47 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37262 R341

PV5470 (continued) R800 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R801

PV5470 (continued) L213 Peaking Coil, 2.2uH., 5% . . . . . . . 4835 150 57054 L214

PV5470 (continued) C587 680pF., 5%, 50V, Ceramic . . . . . . . 4835 122 87019 C588

PV5470 (continued) R905 120k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37055 R906

PV5470 (continued) S T802 Transformer, Dynamic Focus . . . . . . 4835 142 47025S T900

PV5470 (continued) R35 560 ohm, 5%, 1/10W, Metal. . . . . . . 4835 111 37428 R36

00706102 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

PV6070 - Manual no. 7573 CBA's CBA&apos

PV6070 (continued) C109 2.2uF., 20%, 50V, Electrolytic . . . . 3198 025 52280 C110

PV6070 (continued) R257 330 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37443 R258

PV6070 (continued) HS6 Small Signal Shield. . . . . . . . . . 3135 011 02251 HS100

PV6070 (continued) R4 68 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37408 R5

PV6070 (continued) C375 1000pF., 10%, 50V, Ceramic . . . . . . 3198 017 01020 C377

PV6070 (continued) R52 47k, 5%, 1/10W, Metal Film . . . . . . 4835 111 37445 R53

PV6070 (continued) R340 47 ohm, 5%, 1/10W, Carbon Film . . . . 4835 111 37262 R341

PV6070 (continued) R800 100 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37432 R801

PV6070 (continued) L213 Peaking Coil, 2.2uH., 5% . . . . . . . 4835 150 57054 L214

00706103 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

PV6070 (continued) C587 680pF., 5%, 50V, Ceramic . . . . . . . 4835 122 87019 C588

PV6070 (continued) R905 120k, 5%, 1/4W, Metal Film . . . . . . 4835 111 37055 R906

PV6070 (continued) S T802 Transformer, Dynamic Focus . . . . . . 4835 142 47025S T900

PV6070 (continued) R35 560 ohm, 5%, 1/10W, Metal. . . . . . . 4835 111 37428 R36

XV5270 - Manual no. 7573 CBA's CBA&apos

XV5270 (continued) C111 0.1uF., 50V, Ceramic . . . . . . . . . 3198 023 21040 C112

XV5270 (continued) R259 100 ohm, 5%, 1/3W, Metal Film. . . . . 4835 116 87002 R260

XV5270 (continued) HS100 Spring Clip for Q306 and Q307 (2 used) 3135 011 03270 HS150

XV5270 (continued) 16 Frame f/Digital Convergence. . . . . . 4835 432 17846 9

XV5270 (continued) C363 100pF., 5%, 50V, Ceramic . . . . . . . 3198 016 01010 C375

00706104 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

XV5270 (continued) R49 100 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57684 R51

XV5270 (continued) R338 470 ohm, 5%, 1/10W, Carbon Film. . . . 4835 111 37259 R339

XV5270 (continued) R789 150 ohm, 5%, 1/2W, Metal Film. . . . . 4835 116 57696 R790

XV5270 (continued) L208 Peaking Coil, 12uH., 5%. . . . . . . . 4835 150 57058 L209

XV5270 (continued) C565 2200pF., 10%, 50V, Ceramic . . . . . . 4835 122 87083 C567

XV5270 (continued) S R825 1 ohm, 5%, 1/2W, Metal Film. . . . . . 4835 116 57441 R826

XV5270 (continued) L550 Suppression Coil, 10uH.. . . . . . . . 4835 152 27002 L803

XV5270 (continued) R23 820 ohm, 5%, 1/10W, Metal. . . . . . . 4835 111 37466 R24

00706105 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

00706109 0001, 0002 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422

00706115 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

TV SAFETY NOTES SAFETY CHECKS After the original service problem has been corrected, a complete safety check should be made. Be sure to check over th

00706116 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

00706120 0001 OPTICAL ASSEMBLY "s" in the "s" column indicates a safety part. Ill.# s Part Number Description s 2422 549 43

PICTURE TUBE REPLACEMENT Exploded view of optical assembly. Replacement of the Picture Tube (CRT) and/or Optical system components of a Projection

DISASSEMBLY PROCEDURE Exploded view of optical assembly. Removal of a single CRT/Lens Assembly from the light rack 1a) Remove AC power from the

SERVICING THE CRT/OPTICAL ASSEMBLY The following procedures describe how to service the Delta 77/78 CRT/Optical block used in the PTV 700 Series Chas

12b) Use an empty coupling fluid bottle to extract the remainder of the fluid from the coupler. Note: Complete removal of the coupling fluid is not n

Repair or Replacement of The Optical/Coupler Assembly 1e) Remove PTV Coupling Fluid as described above in steps 1b through 13b of the "removing

7f) Tighten the bolts in a star pattern. 8f) Lay the CRT assembly on its side with the drain plug pointing up. 9f) Remove the drain plug (1/4 turn t

ADJUSTMENT PROCEDURES The Large Signal Panel incorporates a "Hot" ground system. Always use a separate isolation transformer when applying

2 TUNER TEST POINT LOCATION GRAPHIC 1. Turn the set on and tune to a TV signal. 2. Connect a Digital Voltmeter to TP41 on the Small Signal Panel

5. When troubleshooting and making test measurements in a receiver with a problem of excessive high voltage, reduce the line voltage by means of a Var

1. Tune to a weak station, or loosely couple the antenna to observe a snowy picture. 2. Set the R.F. AGC Delay (R256) to its fully counter- clockwis

Two Tuner Models (ASG053, & 54) Tuner 1 1. Use the VCO and AFT adjustment procedure described under Single Tuner Models for alignment of Tuner 1

Sound Alignment Single Tuner Models (ASG051 & 52) Note: This control (L201) is located on the Small Signal Panel in zone area J2. 1. Select an

+130Vdc B+ Adjust Note: This control (R455) is located on the Large Signal Panel in zone area A-6. Upon replacement of the Large Signal Panel, or

High Voltage Adjustment Procedure: EXERCISE EXTREME CAUTION WHEN ADJUSTING HIGH VOLTAGE. NOTE: THE FOLLOWING TEST EQUIPMENT MUST BE USED: • A Hig

High Voltage Frequency Adjustment Note: This control (R901) is located on the Large Signal Panel in zone area H-3. 1. Turn the set off and disconne

PROGRAMMING FACTORY DEFAULT VALUES The chassis is controlled by an on-board microcomputer and peripheral parts, altogether known as a "tuning sy

Adjustment of Registers in Service Mode: When the receiver is operating in the service mode, all normal on-screen displays are suppressed and replaced

A Tuner not responding to IIC. B EEPROM (IC304) not responding to IIC. C IC120 (Stereo Decoder IC) not responding to IIC. D IC1001 (PIP Module) not r

Sub-Contrast Alignment 1. Enter the Service Mode via the previous procedure (06-25-96-Menu) and apply an NTSC Color Bar Pattern Signal to the antenna

PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) Some semiconductor solid state devices can be damaged easily by static electricity. Such components commo

STEREO DECODER ALIGNMENTS Note: The following procedure was performed with a Sencore VG91 Universal Video Generator and must be performed while the u

Spectrum 1. With the VG91 Generator still connected to the tuner input and the oscilloscope to TP102 (Pin 38 of IC200), turn the set ON. 2. Set the

GRAY SCALE AND BLACK AND WHITE TRACKING (G2 ADJ) Note: Perform Electrical and Optical Focus before attempting this adjustment. 1. Remove the Light B

CENTERING, GEOMETRY, AND CONVERGENCE ADJUSTMENTS Important: Unlike many previous PTV systems, the 770-790 series PTV incorporates a Digital Converge

CONVERGENCE SERVICE MODE PROCEDURES Note: This procedure is required for all of the following geometry and convergence adjustments. Using the remote t

4. The highlighted adjustment Icon (Cross) should be illuminated on the middle left side of the screen. Make the necessary Convergence Adjustments u

CRT SCREEN CENTERING (Mechanical) 1. Locate the Screen Center by placing strings diagonally across the viewing area of the screen from corner to cor

GREEN GEOMETRY The Green Geometry must be accurately adjusted to achieve proper convergence and screen geometry. The Red and Blue displays will indiv

9. Remove the 7" X 7" piece of cardboard from the Blue Output Lens and cover the Red Lens. 10. Repeat the procedure in steps 5 and 6 by adj

Clock Calibration The microcomputer's crystal oscillator frequency of approx. 12MHz is applied to a divider program (within the micro) in order

PRACTICAL SERVICE PRECAUTIONS IT MAKES SENSE TO AVOID EXPOSURE TO ELECTRICAL SHOCK. While some sources are expected to have a possible dangerous impa

Table 1-0: Factory Register Definitions REG. DESCRIPTION VAL. (HEX) NOTES 00 EXIT 1A 00 saves data and powers off 01 EXIT DEFAULTS 1A (see Wa

41 V COMP 00 Do Not Modify (must be 00) 42 PICT WIDTH 28 43 E W PARAB 10 Do Not Modify 44 E W CORNERS 00 Do Not Modify 45 TRAPEZIUM 39 Do

Clock Calibration Values If Clock is Fast Freq., Hz. [- Comp.] Cal. Byte (Hex) (sec./day) 2403.84615 00 0.00 2403.84866 01 0.09 2403.85116 02

2403.93880 25 3.33 2403.94131 26 3.42 2403.94381 27 3.51 2403.94631 28 3.60 2403.94882 29 3.69 2403.95132 2A 3.78 2403.95383 2B 3.87 240

2404.05399 53 7.47 2404.05649 54 7.56 2404.05899 55 7.65 2404.06150 56 7.74 2404.06400 57 7.83 2404.06651 58 7.92 2404.06901 59 8.01 240

If Clock is Slow Freq., Hz. [- Comp.] Cal. Byte (Hex) (sec./day) 2403.84615 80 0.00 2403.84365 81 0.09 2403.84115 82 0.18 2403.83864 83 0.27

2403.74599 A8 3.60 2403.74349 A9 3.69 2403.74099 AA 3.78 2403.73848 AB 3.87 2403.73598 AC 3.96 2403.73347 AD 4.05 2403.73097 AE 4.14 240

2403.63081 D6 7.74 2403.62831 D7 7.83 2403.62580 D8 7.92 2403.62330 D9 8.01 2403.62079 DA 8.10 2403.61829 DB 8.19 2403.61579 DC 8.28 240

CIRCUIT DESCRIPTION PTV Introduction The PTV800 series Projection TV Chassis was developed by Philips/Magnavox Consumer Electronics for the 1998 mod

The Microcomputer IC300 develops the RGB and Fast Blanking signals for the On-Screen Graphics. White Balance is adjusted at the output of the NTSC S