Philips AZ2555/17 User Manual download pdf

• Dès que l’achat de votre appareil

Philips est enregistré, vous avez droit à

tous les avantages dont bénéficient les

possesseurs des produits Philips.

• Remplissez et renvoyez votre carte

d’enregistrement de garantie jointe à

votre appareil sans tarder et vous béné-

ficierez de ces avantages importants.

Renvoyez votre carte d’enregistrement de garantie pour vous

assurer de recevoir tous les avantages auxquels vous avez droit.

Vérification

de garantie

Enregistrez votre produit

dans les 10 jours pour

confirmer votre droit à

une protection maximum

selon les termes et les

conditions de votre

garantie Philips.

Confirmation

de possession

Votre carte d’enreg-

istrement de garantie

prouve que vous possédez

l’appareil en cas de vol ou

de perte du produit.

Enregistrement

du modèle

Renvoyez votre carte d’en-

registrement de garantie dès

aujourd’hui pour vous assur-

er de recevoir toutes les

informations, les offres et les

bonus auxquels vous avez

droit en tant que possesseur

de ce modèle.

Cet « éclair à pointe de

flèche » indique qu’un matéri-

au non isolé, situé à l’intérieur

de l’unité, risque de provoquer un choc

électrique. Pour la sécurité de chacun,

nous vous prions de ne pas retirer le

boîtier de ce produit.

Le « point d’exclamation »

attire votre attention sur des

sujets risquant de provoquer

des problèmes de f

onctionnement et

d’entretien si vous ne lisez pas les infor-

mations s’y reportant.

DANGER: NE PAS EXPOSER

CET ÉQUIPEMENT A LA PLUIE NI A

UNE HUMIDITÉ EXCESSIVE POUR

ÉVITER LES RISQUES D’INCENDIE

ET DE CHOC ÉLECTRIQUE.

ATTENTION: Pour éviter les

chocs électriques, introduire la lame la

plus large de la fiche dans la borne

correspondante de la prise et pousser

jusqu’au fond.

Cet espace vous est réservé

Inscrivez ci-dessous le numéro de série situé

à l’arrière du bloc. Conservez cette informa-

tion pour vous y reporter à l’avenir.

N° de modèle ____________________

N° de série ______________________

MAC5097

Connaissez ces

symboles de

ssééccuurriittee

ATTENTION

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER

LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE

PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A

UN TECHNICIEN QUALIFIE.

• Una vez que se registre la compra de

su aparato Philips, Ud. tiene derecho a

todas las ventajas correspondientes al

dueño de un producto Philips.

• Sírvase llenar y devolver en seguida

la Tarjeta de Registro de la Garantía

empacada con su aparato y saque

provecho de estas ventajas importantes.

Envie hoy su Tarjeta de Registro de la Garantía

para recibir todas las ventajas correspondientes.

Verificación

de la garantía

Registre su producto den-

tro de 10 días para confir-

mar su derecho a máxima

protección bajo los térmi-

nos y condiciones de la

garantía de Philips.

Confirmación

del dueño

Su Tarjeta de Registro de

la Garantía comprueba

que Ud. es el dueño del

aparato en caso de robo

o pérdida del producto.

Registro

del modelo

La devolución inmediata de

su Tarjeta de Registro de la

Garantía le garantiza que

recibirá toda la información

y todas las promociones

especiales que le corre-

sponden por ser el dueño

de su modelo.

El símbolo del «rayo» indica

que algún material no aislado

dentro de su unidad podría

resultar en una sacudida eléctrica. Para

la seguridad de todos, favor de no

remover la cubierta del producto.

El «signo de exclamación» le

llama la atención a carac-

terísticas sobre las que Ud.

debe leer la información adjunta

detenidamente para evitar problemas

de funcionamiento y mantenimiento.

ADVERTENCIA: PARA EVI-

TAR EL RIESGO DE SACUDIDA

ELECTRICA O INCENDIO, NO

EXPONGA ESTE EQUIPO A LLUVIA

NI A HUMEDAD.

PRECAUCION: Para evitar

sacudida eléctrica, introduzca la patilla

ancha del enchufe al fondo de la ranu-

ra ancha.

Para uso del cliente:

Escriba abajo el número de serie que se

encuentra en el panel posterior. Guarde

esta información para el futuro.

No. de modelo ____________________

No. de serie ______________________

MAC5097

Conozca estos

simbolos de

seguridad

PRECAUCION

RIESGO DE SACUDIDA ELECTRICA

NO ABRIR

PRECAUCION: PARA REDUCIR EL RIESGO DE SACUDIDA ELECTRICA,NO RETIRE

LA CUBIERTA (NI EL PANEL POSTERIOR). ESTE APARATONO CONTIENE NINGUNA

PARTE QUE PUEDA SER REPARADA POREL USARIO. DE SER NECESARIO ALGUN

SERVICIO O REPARACIONDEL APARATO, LLEVELO UN TECNICO CALIFICADO.

• Once your Philips purchase is registered,

you’re eligible to receive all the privileges

of owning a Philips product.

• So complete and return the Warranty

Registration Card enclosed with your

purchase at once, and take advantage

of these important benefits.

Return your Warranty Registration card today to

ensure you receive all the benefits you’re entitled to.

Warranty

Verification

Registering your product

within 10 days confirms

your right to maximum

protection under the

terms and conditions of

your Philips warranty.

Owner

Confirmation

Your completed Warranty

Registration Card serves

as verification of owner-

ship in the event of prod-

uct theft or loss.

Model

Registration

Returning your Warranty

Registration Card right

away guarantees you’ll

receive all the information

and special offers which

you qualify for as the

owner of your model.

This “bolt of lightning” indi-

cates uninsulated material

within your unit may cause

an electrical shock. For the safety of

everyone in your household, please do

not remove product covering.

The “exclamation point” calls

attention to features for

which you should read the

enclosed literature closel

y to prevent

operating and maintenance problems.

WARNING: TO PREVENT

FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE.

CAUTION: To prevent electric

shock, match wide blade of plug to

wide slot, and fully insert.

For Customer Use

Enter below the Serial No. which is locat-

ed on the rear of the cabinet. Retain this

information for future reference.

Model No. _______________________

Serial No. ________________________

MAC5097

Know these

ssaaffeettyy

symbols

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Class II equipment symbol

This symbol indicates that the unit has a double insulation system.

Símbolo del equipo Clase II

Este símbolo indica que la unidad tiene un sistema doble de aislamiento.

Symbole d’ un appareil de classe II

Ce symbole indique que l’appareil est équipé d’un système à double isolation.

1. Lea estas instrucciones.

2. Conserve estas instrucciones.

3. Lea todos los avisos.

4. Siga todas las instrucciones.

5. No utilice este aparato cerca del

agua.

6. Para limpiar el aparato utilice sólo

un trapo seco.

7. No tape las aperturas de venti-

lación. Proceda a su instalación de

acuerdo con las instrucciones del

fabricante.

8. No instale el equipo cerca de fuentes

de calor – Como radiadores, calentadores,

estufas o cualquier otro aparato (incluyen-

do los amplificadores) generador de calor.

9. No anule la

seguridad de la

clavija de corriente

(ya sea de tipo polar-

izado o

con toma de tierra). Las clavijas polarizadas

tienen dos patillas, una más ancha que la

otra. Las que disponen de toma de tierra

tienen dos patillas y una tercera que es la

de conexión a tierra.Tanto la patilla más

ancha como la toma de tierra han sido

incorporadas a la clavija para su seguridad

personal. Si la clavija suministrada con el

equipo no es compatible con su toma de

corriente, consulte a un electricista para

sustituir la toma de corriente obsoleta.

10.

Proteja debidamente el cable impi-

diendo que pueda pisarse o incluso per-

forarse, especialmente en la parte más

próxima a la clavija y en el punto de salida

del equipo.

11. Utilice exclusivamente aquellos dis-

positivos/ accesorios recomendados

por el fabricante.

12.

Coloque el equipo exclusi-

vamente sobre aquellos carros,

bases, trípodes, soportes o

mesas especificados por el com-

erciante o vendidos con el

equipo. Cuando utilice un carro,

tenga cuidado al desplazar el

conjunto carro/ equipo para evi-

tar posibles daños por vuelco.

13 .

Desenchufe el aparato durante tor-

mentas eléctricas o cuando no vaya a ser

utilizado durante largo tiempo.

14 .

Confíe el mantenimiento y las

reparaciones a personal técnico especial-

izado. El equipo deberá repararse siempre

que haya resultado dañado de alguna man-

era, como por ejemplo por daños en el

cable o en la clavija, por derrame de líqui-

do sobre el equipo, por objetos que

hubieran podido introducirse en su interior,

por exposición del equipo a la lluvia o a

ambientes húmedos, cuando el equipo no

funcione con normalidad o cuando hubiera

sufrido algún tipo de caída.

15.

Uso de las pilas – ADVERTENCIA:

Para

prevenir escapes en las pilas, que pueden

ocasionar lesiones físicas, daños a

su propiedad o dañar la unidad:

● Instale todas las pilas correctamente, + y -

como está marcado en la unidad.

● No mezcle las pilas (viejas con nuevas o

de carbono y alcalinas, etc.).

● Extraiga las pilas cuando no vaya a usar la

unidad durante largo tiempo.

EL 6475-S003: 02/8

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near

water.

6. Clean only with dry cloth.

7. Do not block any ventilation open-

ings. Install in accordance with the

manufacturer´s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that

produce heat.

9. Do not defeat

the safety

purpose of the

polarized or

grounding-type plug. A polarized plug has

two blades with one wider than the other.

A grounding type plug has two blades and

a third grounding prong.The wide blade or

the third prong are provided for your safe-

ty. If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10.

Protect the power cord from being

walked on or pinched, particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11.

Only use attachments/accessories

specified by the manufacturer.

12.

Use only with the cart,

stand, tripod, bracket, or table

specified by the manufacturer or

sold with the apparatus. When a

cart is used, use caution when

moving the cart/apparatus com-

bination to avoid injury from

tip-over.

13 .

Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14 .

Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is dam-

aged, liquid has been spilled or objects

have fallen into the apparatus, the appara-

tus has been exposed to rain or moisture,

does not operate normally, or has been

dropped.

15.

Battery usage CAUTION – To prevent

battery leakage which may result in bodily

injury, property damage, or damage to the

unit:

● Install all batteries correctly, + and - as

marked on the unit.

● Do not mix batteries (old and new or

carbon and alkaline, etc.).

● Remove batteries when the unit is not

used for a long time.

EL 6475-E004: 02/8

IMPORTANT SAFETY INSTRUCTIONS

1. Lisez ces instructions.

2. Conservez ces instructions.

3. Respectez les avertissements.

4. Suivez toutes les instructions.

5. N’utilisez pas cet appareil à proximité d’une

source d’eau.

6. Nettoyez l’appareil uniquement avec un chif-

fon sec.

7. N’obstruez aucun orifice de ventilation.

Installez l’appareil selon les instructions du

fabricant.

8. N’installez pas l’appareil près d’une source de

chaleur comme par exemple des radiateurs, bouches

de chaleur, cuisinières, ou autres appareils (même des

amplificateurs) dégageant de la chaleur.

9. Ne détruisez pas la sécurité incorporée dans la

prise de terre ou prise

polarisée fournie. Une

prise polarisée est dotée de

deux lames

dont une plus large que l’autre. Une prise de terre est

dotée de deux fiches semblables et d’une troisième,

plus large, qui assure la mise à la terre pour votre

sécurité. Si la prise fournie ne convient pas à la prise

murale dont vous disposez, consultez un électricien

pour remplacer et adapter votre prise murale.

10.

Protégez le cordon d’alimentation pour éviter

de marcher dessus ou de le pincer particulièrement

aux endroits des prises, mâles et femelles, et au point

de raccordement sur l’appareil lui-même.

11.

Utilisez uniquement des accessoires ou

options recommandés par le fabricant.

12.

Utilisez uniquement un meuble

sur roulettes, un support, un pied, une

étagère ou une table de type recom-

mandé par le fabricant. Si vous utilisez un

meuble sur roulettes, veillez à le déplacer

avec précaution afin d’éviter tout acci-

dent corporel si l’équipement se renver-

sait.

13.

Débranchez l’appareil pendant les orages ou s’il

doit rester inutilisé pendant une période de temps

prolongée.

14.

Pour toute réparation, faites appel à un personnel

qualifié. Une réparation sera nécessaire si l’appareil a

subi des dommages tels que détérioration du cordon

d’alimentation ou de la prise, liquide renversé sur l’ap-

pareil, ou encore si un objet est tombé dessus, si l’ap-

pareil a été exposé à la pluie ou à l’humidité, s’il ne

fonctionne pas correctement ou s’il a fait une chute.

15.

PRÉCAUTION d’emploi des piles – Afin d’éviter

toute fuite des piles qui risquerait de causer des

blessures corporelles, des dommages matériels, ou

d’endommager l’appareil :

● Installez toutes les piles correctement, + et - tels

qu’indiqués sur l’appareil.

● Ne mélangez pas les piles (pas de piles neuves avec

des usagées ou de piles au carbone avec des alca-

lines, etc.).

● Enlevez les piles lorsque l’appareil reste inutilisé pen-

dant une longue période.

EL 6475-F003: 02/8

CONSIGNES DE SÉCURITÉ IMPORTANTES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PHILIPS CONSUMER ELECTRONICS NORTH AMERICA

Knoxville, Tennessee 37914-1810, U.S.A.

AZ2555

CD Soundmachine

Need help? Call us!

Philips representatives are ready to help you with

any questions about your new product. We can guide you

through Connections, First-time Setup, or any of the Features.

We want you to start enjoying your new product right away!

CALL US BEFORE YOU CONSIDER

RETURNING THE PRODUCT!

1-800-531-0039

Visit us on the web at www.philips.com

Return

your Warranty

Registration Card

within 10 days

Printed in China

CLASS 1

LASER PRODUCT

AZ 2555

3140 115 3015.2

English Français Español

AC Polarized

Plug

Prise

polarisée C.A.

English:This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus as set out in the Radio Interference Regulations of the

Canadian Department of Communications.

Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur

le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada.

Canada

Clavija

polarizada

de CA

Meet Philips at the Internet

http://www.philips.com

PORTABLE AUDIO

One Year Free Exchange

This product must be carried in for an exchange.

LIMITED WARRANTY

WHO IS COVERED?

You must have proof of purchase to exchange the product.

A sales receipt or other document showing that you pur-

chased the product is considered proof of purchase.Attach

it to this owner’s manual and keep both nearby.

WHAT IS COVERED?

Warranty coverage begins the day you buy your product.

For one year thereafter, a defective or inoperative product

will be replaced with a new, renewed or comparable prod-

uct at no charge to you.A replacement product is covered

only for the original warranty period.When the warranty

on the original product expires, the warranty on the

replacement product also expires.

WHAT IS EXCLUDED?

Your warranty does not cover:

• labor charges for installation or setup of the product,

adjustment of customer controls on the product, and

installation or repair of antenna systems outside of the

product.

• product repair and/or part replacement because of

misuse, accident, unauthorized repair or other cause

not within the control of Philips.

• reception problems caused by signal conditions or

cable or antenna systems outside the unit.

• a product that requires modification or adaptation to

enable it to operate in any country other than the

country for which it was designed, manufactured,

approved and/or authorized, or repair of products

damaged by these modifications.

• incidental or consequential damages resulting from the

product. (Some states do not allow the exclusion of

incidental or consequential damages, so the above

exclusion may not apply to you.This includes, but is not

limited to, prerecorded material, whether copyrighted

or not copyrighted.)

• a product used for commercial or institutional purposes.

WHERE IS EXCHANGE AVAILABLE?

You may exchange the product in all countries where the

product is officially distributed by Philips. In countries

where Philips does not distribute the product, the local

Philips service organization will attempt to provide a

replacement product (although there may be a delay if the

appropriate product is not readily available).

BEFORE REQUESTING EXCHANGE...

Please check your owner's manual for assistance. If you

have additional questions, call us at 1-800-531-0039.

EXCHANGING A PRODUCT IN U.S.A.,

PUERTO RICO, OR U.S.VIRGIN ISLANDS...

Contact 1-800-531-0039 to arrange an exchange. Or, ship

the product, insured and freight prepaid, and with proof of

purchase enclosed, to the address listed below.

Philips Exchange Program

Suite A

406 North Irish Street

Greeneville TN 37745

(In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied war-

ranties, including implied warranties of merchantability and fit-

ness for a particular purpose, are limited in duration to the

duration of this express warranty. But, because some states do

not allow limitations on how long an implied warranty may

last, this limitation may not apply to you.)

EXCHANGING A PRODUCT IN CANADA...

Please contact Philips at:

1-800-661-6162 (French Speaking)

1-800-531-0039 (English or Spanish Speaking)

(In Canada, this warranty is given in lieu of all other war-

ranties. No other warranties are expressed or implied,

including any implied warranties of merchantability or fit-

ness for a particular purpose. Philips is not liable under any

circumstances for any direct, indirect, special, incidental or

consequential damages, howsoever incurred, even if notified

of the possibility of such damages.)

REMEMBER...

Please record below the model and serial numbers found

on the product.Also, please fill out and mail your warranty

registration card promptly. It will be easier for us to notify

you if necessary.

MODEL # __________________________________

SERIAL # __________________________________

EL6095T004 / 8-02

This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province.

Philips, P.O. Box 520890, Miami, FL 33152, USA,

(402) 536-4171

3. EQUALIZER

To adjust the bass, mid and treble frequencies press

EQUALIZER once or more, then rotate VOLUME

within 3 seconds to adjust each level.

=Display briefly shows

, or

level (-5 to +5) or .

Note: EQUALIZER can be used during TUNER, CD,

USB PC LINK and GAME

•AUX source.

4. GAMESOUND

To adjust the game sound, press GAMESOUND once

or more to select your option.

=Display briefly shows

, ,

Note: GAMESOUND is only available when you

play in GAME

•

AUX source.

How to MUTE the sound

1. Press MUTE on the remote control to interrupt

sound reproduction instantly.

= Playback continues without sound and the

display flashes .

2. To reactivate sound reproduction you can:

– press MUTE again;

– adjust the volume controls;

– press

in CD / USB PC LINK source;

– change to another source.

DIGITAL TUNER (See 3)

Tuning to stations

1. Press STANDBY ON

to on, then press

SOURCE once or more to select TUNER (or press

TUNER once on the remote control).

= Display: shows briefly followed by

waveband, frequency, and preset station

number if already stored.

2. Press FM

•

AM once or more to select your

waveband. (TUNER on the remote control)

3. Tuning to stations: you can tune to your

stations manually or by automatic search tuning:

Press down on

∞ or §

I and release button when

the frequency in the display starts running.

= The radio automatically tunes to a station of

sufficient reception. Display shows

during automatic tuning.

4. Repeat step 3 if necessary until you find the

desired station.

• To tune to a weak station, press

∞ or §

briefly

and repeatedly until you have found optimal

reception.

To improve radio reception:

• For FM, extend, incline and turn the telescopic

antenna. Reduce its length if the signal is too

strong.

• For AM, the set uses a built-in antenna. Direct this

antenna by turning the whole set.

Programming tuner stations:

You can store up to a total of 30 radio stations in the

memory, manually or automatically (Autostore).

Autostore

Automatic programming will start from preset 1 or a

chosen preset number. From this preset number

upwards, former programmed tuner stations will be

erased. The set will only program stations which are

not in the memory already.

1. Press PRESET- or + once or more to select the

preset number where programming should start.

Note: If no tuner preset number is selected, default

is preset 1 and all your presets will be erased.

2. Press PROG for 4 seconds or more to activate

auto store programming.

= Display: is shown and available

stations are programmed in order of waveband

FM, followed by AM , the first preset station

will then be played after all stations are stored

automatically.

Manual programming

1. Tune to your desired station (see Tuning to

stations).

2. Press PROG to activate programming.

= Display: PROG flashes.

3. Press

PRESET -/+

once or more to allocate a

number from 1 to 30 to this station.

4. Press PROG again to confirm.

= Display: shows the preset number, waveband

and the frequency of the preset station.

5. Launch MUSICMATCH JUKEBOX and create

your own playlist of favorite songs by dragging and

dropping the music track from anywhere on your PC

into the playlist window.

Note:

-- If you encounter any problem using the USB PC LINK,

please refer to the FAQ (Frequently Asked Questions)

stored in your USB PC LINK installer disc or visit

www.audio.philips.com for the latest FAQ updates .

After setup, refer to "Connecting to USB PC Link"

for details on the USB PC LINK operations.

Enable digital CD audio output

Before playing CDs on your PC’s CD-ROM drive, it is

necessary to configure your PC’s hardware as follows:

For Windows ME/ 2000/ XP

1. Enter the system panel menu and select

'SYSTEM', 'PROPERTIES', 'HARDWARE',

'DEVICE MANAGER', 'CD-ROM DRIVES' and

'PROPERTIES'.

For Windows 98

2. Check the Enable digital CD audio for this CD-

ROM device setting option is selected (enabled).

Note:-For windows 98 you may need to refer to

your PC's manual for correct configuration.

Connecting to USB PC Link (See 9)

The USB PC LINK allows you to playback your music col-

lection from the PC via the powerful amplifier and speak-

ers of this system.

IMPORTANT!

Make sure the MusicMatch software has been

installed. Refer to "Quick Setup Guide" for the

USB PC Link.

1. Turn on your set and computer .

] Check your PC volume is suitably adjusted and

not set to minimum / mute.

2. Press SOURCE (USB on the remote control) once

or more to select USB PC LINK .

3. If correctly connected your PC will automatically

launch MUSICMATCH JUKEBOX.

] If the audio streaming is detected, the current

track name scrolls .

]If scrolls for a while, check the

connection between your PC and set.

4. Press

¡ or ™

until the desired track in the playlist is

highlighted.

5. Press

to start playback.

] The track time appears and the track name scrolls

once.

Note: The display only supports English characters

in uppercase.

6. If you want to see the track details displayed press

MODE.

During playback,

– Press SHUFFLE on the remote control to play all

available tracks in the playlist in random order.

– Press REPEAT on the remote control to repeat

playback all the tracks in the playlist.

7. To cancel play modes/ stop playback, press

9 or

select another sound sources.

MAINTENANCE & SAFETY (See 0)

CD player and disc handling

• If the CD player cannot read CDs correctly, use a

cleaning CD to clean the lens before taking the set to

repair.

• The lens of the CD player should never be touched!

• Sudden changes in the surrounding temperature can

cause condensation on the lens of your CD player.

Playing a CD is then not possible. Do not attempt to

clean the lens but leave the set in a warm

environment until the moisture evaporates.

• Always close the CD door to avoid dust on the lens.

• To take a CD out of its box, press the center spindle

while lifting the CD.

• To clean the CD, wipe in a straight line from the center

towards the edge using a soft, lint-free cloth. Do not

use cleaning agents as they may damage the disc.

• Never write on a CD or attach any stickers to it.

Safety Information

• Don't expose the set, batteries, CDs to humidity, rain,

sand or excessive heat.

• Clean the set with a dry cloth. Don't use any

cleaning agents containing alcohol, ammonia,

benzene or abrasives as these may harm the set.

• Place the set on a hard and flat surface so that the

system does not tilt. Make sure there is good

ventilation to prevent the set from overheating.

USB PC LINK

MAINTENANCE & SAFETY

5. Repeat the above four steps to store other

stations.

Note : You can erase a preset station by storing

another frequency in its place.

To listen to a preset station

Press

PRESET -

once or more until the desired

preset station is displayed.

CD Operation

Playing a CD

This CD player plays Audio Discs including

CD-Recordables and CD-Rewritables.

1. Press

STANDBY ON y

once or more to on, then

select CD SOURCE.

2. Press OPEN

•

CLOSE to open the CD door.

] is displayed when the CD door is

open.

3. Insert a CD with the printed side facing up and press

down on OPEN

•

CLOSE to close the CD door.

]Display show , then scrolls

,or

if no CD inserted/ CD dirty,

incorrectly inserted or damaged.

4. Press

to start playback.

5. To pause playback press

. Press

again to

resume play.

= Time digits flashes during pause.

6. To stop CD playback, press

Note: CD play will also stop when:

– the CD door is opened

– the CD has reached the end

– you select an other sound source.

Selecting a different track

• Press SEARCH

∞ or §

(on the remote control

or ™

) once or repeatedly until the desired track

number appears in the display.

• If you have selected a track number shortly after

loading a disc or in the PAUSE position, you will

need to press

to start playback.

Finding a passage within a track

1. Press and hold SEARCH

∞ or §

– The CD is played at high speed and low volume.

2. When you recognize the passage you want,

release

∞ or §

. Normal playback continues.

Note: During a CD program or if SHUFFLE/ REPEAT

is active, searching is only possible within the same

track.

Different play modes: SHUFFLE and REPEAT (See

4 - 7)

You can select and change the various play modes

before or during playback. The play modes can also be

combined with PROGRAM.

SHUFFLE - tracks of the entire CD/ program are

played in random order

SHUFFLE REPEAT ALL - to repeat the entire CD/

program continuously in random order

REPEAT ALL - repeats the entire CD/ program

REPEAT - plays the current track continuously

1. To select play mode, press MODE once or more.

(SHUFFLE / REPEAT on the remote control).

2. Press

to start playback if in the stop position.

]If you have selected SHUFFLE, playback starts

automatically.

3. To select normal playback, press MODE

repeatedly until the various modes are no longer

displayed.

– You can also press the

to cancel your play

mode in playing.

Programming track numbers

Program in the stop position to select and store your

CD tracks in the desired sequence. If you like, store

any track more than once. Up to 20 tracks can be

stored in the memory.

1. Press SEARCH

∞ or §

on the set to select your

desired track number.

2. Press PROG to confirm the track number to be

stored.

=Display: The number of the tracks programmed

and the total playing time of programmed tracks

SUPPLIED ACCESSORIES

– remote control

– USB cable

– video cable

– CD-ROM USB PC LINK installers

TOP AND FRONT PANEL (See 1)

- 3.5 mm stereo headphone jack.

Note: The speakers will be muted when headphones

are connected to the set.

2 VOLUME

-adjust volume level or equalizer level

(BASS/ MID /HIGH)

3 STANDBY ON y - switch the set on/ off.

4 SOURCE - selects sound source for functions: CD/

TUNER/ USB PC LINK/ GAME •AUX

5 IR SENSOR -infrared sensor for remote control

6 LCD Display - shows the status of the set

7 [dB]: - display to indicate bass power.

8 PRESET

-, + - selects a preset radio station.

SEARCH ∞ , §

CD: - searches backward or forward within a track;

- skips to the beginning of a current track/ previous/

later track.

USB PC LINK - skips to the beginning of a previous/

later track.

TUNER: -

tunes to radio stations

2;- s

tarts or pauses CD / USB PC LINK playback

9 - stop

CD / USB PC LINK

playback;

- erases a CD program.

MODE - selects different CD play modes: e.g.

REPEAT or SHUFFLE order.

- shows current track name in USB PC

LINK mode

9 USB - connect the supplied USB cable here to the

USB port of your computer

0 GAMESOUND - select sound effects: BLAST/

PUNCH/ SPEED/ NORMAL in GAME •AUX mode

WOOX - selects special bass enhancement on/ off

EQUALIZER - selects bass, mid and treble

frequencies, and volume BASS/ MID /HIGH/ VOL

PROG

CD: -

programs tracks and reviews the

programmed songs;

TUNER: -

programs preset radio stations.

FM•AM - selects FM / AM waveband

! AUDIO IN ( LEFT / RIGHT) - LINE-IN jack for

external audio appliance.

VIDEO IN - to keep video plug in place

@ OPEN•CLOSE – press to open/ close CD door

BACK PANEL (See 1)

# Telescopic antenna - improved FM reception

$ Battery compartment - for 8 batteries, type

R-20, UM-1 or D-cells

% AC MAINS - inlet for power cord

^ VIDEO OUT- connect to the VIDEO IN jack on a

TV or VCR for viewing or recording.

REMOTE CONTROL (See 1)

1 CD - selects CD sound source

TUNER - selects tuner source / wavebands

USB - selects USB PC LINK

AUX - selects GAME •AUX

2 y -switches the set to standby / on if set

operating on AC power. (Switches set off only if

battery powered)

3 REPEAT - repeat all tracks in USB PC LINK source

or selects the repeat modes in CD source

SHUFFLE - plays CD tracks in random order in CD /

USB PC LINK source

MUTE - interrupts/ resumes sound

4 VOL 4, 3 -- adjust volume level or adjust equalizer

level (BASS/ MID /HIGH)

5 ¡ , ™ - select previous/ next track in CD / USB PC

LINK playback

9 - stop CD / USB PC LINK playback;

- erases a CD program.

2; - starts or pauses CD or USB PC LINK playback

5 / 6 - searches backwards/ forwards within a CD

track.

TUNER: -

tunes to radio stations

6 EQUALIZER -- selects bass, mid and treble

frequencies

WOOX -- select special bass enhancement on/ off

GAMESOUND - select sound effects: BLAST/

PUNCH/ SPEED/ NORMAL in game mode

7 PRESET -, +, - selects a previous/ next radio

preset station

CAUTION

Use of controls or adjustments or performance

of procedures other than herein may result in

hazardous radiation exposure or other unsafe

operation.

POWER SUPPLY

Whenever convenient, use the power supply to

conserve battery life. Make sure you remove the

power cord from the set and wall jack before inserting

batteries.

Batteries (not included) (See 1)

• Insert 8 batteries, type R-20, UM-1 or D-cells,

(preferably alkaline) with the correct polarity.

Remote control (See A)

• Insert 2 batteries, type AAA, R03 or UM4

(preferably alkaline).

Incorrect use of batteries can cause electrolyte leak-

age and will corrode the compartment or cause the

batteries to burst.

• Do not mix battery types: e.g. alkaline with carbon

zinc. Only use batteries of the same type for the

set.

• When inserting new batteries, do not try to mix old

batteries with the new ones.

• Batteries contain chemical substances, so

they should be disposed of properly.

Using AC Power

1. Check if the AC power supply, as shown on the

type plate located on the bottom of the set,

corresponds to your local power supply. If it does

not, consult your dealer or service center.

2. If your set is equipped with a voltage selector,

adjust the selector so that it matches with the

local power supply.

3. Connect the power cord to the wall jack and the

set is now ready for use.

4. To disconnect the power supply, unplug the set

from the wall jack.

POWER-SAVING AUTOMATIC STANDBY

As a power-saving feature, the system automatically

switches to standby 15 minutes after CD has reached

the end and no control is operated.

The type plate is located on the bottom of

the set.

BASIC FUNCTIONS

Switching on and off and selecting function

1. Press STANDBY ON

on the set to switch on.

2. Press SOURCE once or more to select your

desired function: CD, TUNER, USB PC LINK or

GAME

•AUX

3. Press STANDBY ON

to switch off the set.

Note : The tone, sound settings, tuner presets and

the volume level (up to a maximum volume level of

VOL 20 ) will be retained in the set's memory.

Adjusting volume and sound (See 2)

1. Adjust the volume with the VOLUME control.

= Display shows the volume level and a

number from 0-32.

2. wOOx

To enhance the bass response: press wOOx once or

more to switch on / off.

= wOOx-key backlight lights up when wOOx is

turned on.

Notes:

- wOOx can be used when you play TUNER, CD, USB

PC LINK and GAME

•AUX source.

- To prevent sound interference the bass control

options operate exclusively. You cannot combine the

bass from EQUALIZER with wOOx

- Some discs might be recorded in high modulation,

which causes a distortion at high volume. If this

occurs, deactivate wOOx or reduce the volume.

English CONTROL

is shown briefly PROG flashes.

=If you attempt to program without first selecting

a track number, is shown.

3. Repeat steps 1-2 to select and store all desired

tracks.

=Display: if you try to program more

than 20 tracks.

4. To start playback of your disc program, press

2; .

Note: During normal playback, you can press PROG

to add a current track to your program list.

Reviewing the program

In stop / play position, press and hold down PROG for

a while until the display shows all your stored track

numbers in sequence.

Erasing a program

You can erase the program by:

• pressing

twice;

= displayed briefly, and PROG

disappears.

• pressing STANDBY ON

• selecting another sound sources

• opening the CD door.

GAMESOUND (See 8)

PLAYING WITH GAMESOUND:

1. Press SOURCE once or more on the set to select

the GAME

•

AUX function (AUX on the remote

control)

=Display scrolls :

2. Connect your console to the cinches on the front

of the set AUDIO IN ( LEFT / RIGHT) and VIDEO

IN.

3. Press GAMESOUND once or more to select your

game sound option.

Display briefly shows , ,

Connecting other equipment to your system

Use the supplied video cable to connect the VIDEO

OUT terminal on the back of the set to VIDEO IN on

a TV or VCR for viewing or recording.

USB PC LINK

Quick Setup Guide

PC system requirements

– USB port with Windows 98 / 98 SE / ME/ 2000/ XP

– Intel Pentium MMXX200 or higher

– CD-ROM drive

– Free hard disk space : 15 MB for the software

Installing MusicMatch software

1. Use the supplied USB cable to connect the set to the

USB port on your computer. (See B)

2. Press SOURCE (USB on the remote control) once or

more to select USB PC LINK.

3. Turn on your PC then insert the supplied USB PC LINK

installer disc in the PC's CD-ROM drive. This

application software can also be downloaded from

http://www.audio.philips.com.

IMPORTANT!

Please use this customized MusicMatch

software for your USB PC Link application.

Remember to un-install all other MusicMatch

jukebox software first from your PC system (if

available).

4. The installation guide will appear automatically. If it

does not, go to the CD-ROM drive in Windows

Explorer and double click on the USB PC LINK.exe.

Then perform the following steps:

– Select your desired language from the list.

– Select installer driver.

– Select installer MusicMatch jukebox.

– Select other options (Tutorial, Free goodies, FAQ).

Note:

- You are advised to read the MusicMatch tutorial

before using it for the first time. Make sure the

volume on your PC is suitably adjusted to ensure

sound output on the set. For optimum performance,

the equalizer function in MusicMatch should be set to

a low level.

CD PLAYER CD PLAYER

GAMESOUND USB PC LINK

TROUBLESHOOTING

POWER SUPPLY BASIC FUNCTIONS DIGITAL TUNER DIGITAL TUNER

No sound /power

– Volume not adjusted

• Adjust the VOLUME

– Power cord not securely connected

• Connect the AC power cord properly

– Batteries flat / incorrectly inserted

• Insert (fresh) batteries correctly

– Headphones connected to the set

• Disconnect headphones

– Electrostatic discharge/interference

• Unplug the set. If batteries inserted, remove batteries

from the battery compartment.. Press and hold

STANDBY ON y

for 10 seconds, then re-plug /

replace battery supply, and try activating the set again.

• When in USB PC LINK mode, check that your PC's

volume is audible and not set to minimum.

• When playing a CD from the PC's CD-ROM drive, refer

to USB PC Link - Enable digital CD audio output.

Severe radio hum or noise

– Electrical interference: set too close to TV, VCR or

computer

• Increase the distance

Remote control does not function properly

– Batteries flat/ incorrectly inserted

• Insert (fresh) batteries correctly

– Distance/ angle between the set too large

• Reduce the distance/ angle

Poor radio reception

– Weak radio signal

• FM: Adjust the FM telescopic antenna

indication

– No CD inserted

•

Insert a suitable disc

– CD badly scratched or dirty

• Replace/ clean CD, see Maintenance

– Laser lens steamed up

• Wait until lens has cleared

The CD skips tracks

– CD damaged or dirty

• Replace or clean CD

– SHUFFLE or PROG is active

• Switch off SHUFFLE / PROG

is displayed in USB PC LINK

mode for more than 10 sconds

• Check the connection between your PC and the set. If

necessary, please refer to the chapter Connecting to

USB PC Link for the initial setup required.

• Make sure the connected PC is turned on and the

MusicMatch software is working.

8 x R20/ UM1/ D CELL

Take care of your CD Soundmachine.

Grip both handles when you carry or

lift the set.

HEAVY !

SISTEMA DE AUDIO PORTATIL

Cambio gratis por un año

Se necesita presentarse en persona con este producto para cambiarlo.

GARANTIA LIMITADA

¿QUIEN TIENE PROTECCION?

Usted debe tener su comprobante de venta para cambiar el

producto. Una nota de venta u otro documento mostrando

que usted compró el producto se considera un comprobante

de venta.Adjúntelo a este manual de instrucciones y reténgalo

a la mano.

¿QUE CUBRE?

La protección bajo la garantía comienza el mismo día en que

usted compra el producto. Durante un año a partir de esta

fecha, se reemplazará un producto inoperante o defectuoso

con otro nuevo, renovado o comparable sin cargo alguno. Un

producto de reemplazo tiene cobertura sólo durante el

período de la garantía original. Una vez que venza la garantía

original del producto, también habrá vencido la garantía del

producto de reemplazo.

¿QUE EXCLUYE LA GARANTIA?

Su garantía no cubre:

• cobros por mano de obra durante la instalación o montaje

del producto, ajuste de los controles del cliente o de

preferencia e instalación o reparación de los sistemas con

antena fuera de la unidad.

• reparación del producto y/o reemplazo de piezas, a raíz

de uso indebido, accidente, reparación no autorizada u

otra causa no bajo el control de Philips.

• problemas de recepción ocasionados por condiciones de

señales o sistemas de cable o de antena fuera de la

unidad.

• un producto que requiera modificación o adaptación para

que opere en un país que no sea el país para el que fue

concebido, fabricado, aprobado y/o autorizado, o la

reparación de productos dañados por tales modificaciones.

• daños incidentales o consecuentes que resulten del

producto. (Algunos estados no permiten la exclusión por

daños incidentales o consecuentes, de modo que es posible

que la exclusión arriba indicada no le sea aplicable a usted.

Esto incluye, sin limitarse, materiales pregrabados con o sin

amparo de derechos de autor.)

• una unidad que se ha usado para fines comerciales o

institucionales.

¿DONDE SE EFECTUA EL CAMBIO?

Usted puede cambiar el producto en todos los países con

distribución oficial del producto por Philips. En países

donde Philips no distribuye el producto, la entidad local de

servicio Philips tratará de darle un producto de reemplazo

(aunque puede haber demora si el producto apropiado no

está fácilmente disponible).

ANTES DE PEDIR UN CAMBIO…

Por favor, consulte su manual del usuario si necesita ayuda.

Si tiene más preguntas, llámenos al 1-800-531-0039.

PARA CAMBIAR UN PRODUCTO EN LOS

EE.UU., PUERTO RICO O LAS ISLAS VIRGENES…

Contacte con el 1-800-531-0039 para concertar un cambio.

También, usted puede enviar el producto con el seguro y

transporte o franqueo prepagados, adjuntando el comprobante

de venta y enviándolo a la dirección a continuación:

Philips Exchange Program

Suite A

406 North Irish Street

Greeneville TN 37745

(En los EE.UU., Puerto Rico o las Islas Vírgenes, toda garantía

implícita, inclusive las garantías implícitas de comerciabilidad y

aptitud para un propósito en particular, están limitadas en

cuanto a duración al plazo de esta garantía expresa. Puesto

que algunos estados no permiten limitaciones sobre la

duración de una garantía implícita, es posible que la limitación

arriba indicada no le sea aplicable a usted.)

PARA CAMBIAR UN PRODUCTO EN EL

CANADA…

Favor de comunicarse con Philips al:

1-800-661-6162 (francófono)

1-800-531-0039 (anglófono o hispanohablante)

(En el Canadá, esta garantía es otorgada en lugar de toda

otra garantía. No se otorga ninguna otra garantía expresa ni

implícita, comprendiéndose aquí ninguna garantía implícita

de comerciabilidad o aptitud para propósito alguno. Philips

no será responsable bajo circunstancia alguna por daños y

perjuicios directos, indirectos, especiales, incidentales o

consecuentes, independientemente de la manera ocasionada,

aún con notificación de la posibilidad de los mismos.)

RECUERDE…

Favor de anotar los números de modelo y serie del

producto en el espacio abajo.También, sírvase llenar y

enviar oportunamente su tarjeta de registro de la garantía.

Así nos será más fácil notificarle en caso de ser necesario.

Modelo No. ________________________________

Serie No. ________________________________

EL6095T004 / 8-02

Esta garantía le otorga derechos legales específ

icos y usted podría gozar de otros derechos que varían de un estado a otro.

Philips, P.O. Box 520890, Miami, FL 33152, USA,

(402) 536-4171

SYSTÈME SONORE PORTABLE

Échange gratuite pendant un an

Il faut porter ce produit à un centre de service pour l’échanger.

GARANTIE LIMITÉE

QUI EST COUVERT ?

Il faudra présenter une preuve d’achat pour pouvoir

bénéficier des services de la garantie. Le reçu, la facture ou

un autre document portant la date d’achat qui prouve que

vous avez bien acheté le produit est considéré comme

preuve d’achat. L’attacher à ce manuel d’emploi et les

garder tous les deux à portée de main.

QU’EST-CE QUI EST COUVERT ?

La couverture de la garantie entre en vigueur le jour où

vous achetez le produit. Pendant un an à compter de cette

date, tout produit défectueux ou qui ne fonctionne pas

sera remplacé par un produit neuf, renouvelé ou un produit

comparable sans frais aucun au consommateur. Un produit

de remplacement n’est couvert que pendant la période

non-écoulée de garantie d’origine. Lorsque la garantie du

produit d’origine vient à terme, la garantie du produit de

remplacement est terminée aussi.

QU’EST-CE QUI EST EXCLU DE LA GARANTIE ?

La garantie ne couvre pas :

• les frais de main d’œuvre pour installer ou préparer,

pour régler les commandes et pour installer ou réparer

les systèmes d’antenne à l’extérieur du produit.

• la réparation du produit et/ou d’une pièce pour cause du

mauvais emploi, d’accident, de réparations non-agréées

ou d’une autre raison qui ne peut pas être contrôlée par

Philips.

• des problèmes de réception dûs à des conditions de signal,

au câble ou aux systèmes d’antenne à l’extérieur de l’unité.

• un produit qui nécessite des modifications ou adaptations

pour lui permettre de fonctionner dans un pays autre que

le pays pour lequel il a été conçu, fabriqué, agréé et/ou

autorisé, ou la réparation des produits endommagés par

de telles modifications.

• des dommages indirects ou conséquents qui résultent du

produit. (Certains états ou provinces ne permettent pas

l’exclusion de dommages indirects ou conséquents. Il est

donc possible que l’exclusion ci-dessus ne s’applique pas au

cas présent. Cela comprend, mais de façon non-limitative,

des enregistrements, qu’ils soient protégés ou non par les

lois sur les droits d’auteur).

• un produit utilisé pour des raisons commerciales ou

institutionnelles.

OÙ L’ÉCHANGE EST-ELLE PROPOSÉE ?

Le produit pourra s’échanger dans tous les pays où le produit

est distribué officiellement par Philips. Dans des pays où

Philips ne distribue pas le produit, l’organisme local de service

Philips tentera de fournir un produit de remplacement (mais

il pourra y avoir des retards si le bon produit n’est pas

facilement disponible).

AVANT DE DEMANDER UNE ÉCHANGE…

Veuillez consulter votre guide d'utilisation pour assistance.

Si vous avez d'autres questions, contactez-nous au

1-800-531-0039.

POUR BÉNÉFICIER DE L’ÉCHANGE GARANTIE

AUX É.-U.,AU PUERTO RICO OU DANS LES

ÎLES VIERGES AMÉRICAINES…

Contactez 1-800-531-0039 pour organiser un échange.

Ou bien, renvoyer le produit, frêt et assurances payés, avec

preuve d’achat incluse, à l’adresse ci-dessous :

Philips Exchange Program

Suite A

406 North Irish Street

Greeneville TN 37745

(Aux É.-U., au Puerto Rico et aux Îles Vierges, toute garantie

implicite, y compris des garanties de vendabilité et d’aptitude

à un but spécifique, est limitée à la durée de cette garantie

explicite. Mais, étant donné que certains états et provinces

ne permettent pas de limité la durée d’une garantie implicite,

cette limitation pourrait ne pas s’appliquer au cas présent.)

POUR BÉNÉFICIER D’UNE ÉCHANGE GARANTIE

AU CANADA…

Veuillez contacter Philips au :

1-800-661-6162 (Francophone)

1-800-531-0039 (Anglophone ou hispanophone)

(Au Canada, cette garantie est consentie à la place de toute

autre garantie.Aucune autre garantie n’est donnée, qu’elle

soit explicite ou implicite, y compris une garantie implicite

de vendabilité ou d’aptitude à un but spécifique. Philips n’est

pas, en aucun cas, responsable des dommages, qu’ils soit

directs ou indirects, spéciaux, secondaires ou conséquents,

quels que soient leurs origines, même en présence d’une

notification de la possibilité de tels dommages.)

RAPPEL IMPORTANT...

Veuillez inscrire ci-dessous les numéros de modèle et de

série qui se trouvent sur le produit même. De plus, veuillez

remplir et renvoyer sans délai la carte d’enregistrement de

garantie. Il nous sera ainsi plus facile de vous contacter en

cas de besoin.

Nº DE MODÈLE _____________________________

Nº DE SÉRIE _____________________________

EL6095T004 / 8-02

Cette garantie vous donne des droits légaux spécifiques et vous pourriez avoir d’autres droits qui varient d’état en état et de province en province.

Philips, P.O. Box 520890, Miami, FL 33152,

É.-U.,

(402) 536-4171

2 x AAA

USB

If a fault occurs, first check the points listed below before taking the set for repair. If you are

unable to remedy a problem by following these hints, consult your dealer or service center.

WARNING: Do not open the set as there is a risk of electric shock! Under no

circumstances should you try to repair the set yourself, as this will

invalidate the warranty.

Note : This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules.These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures :

– Relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.

Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that

may cause undesired operation.

IMPORTANT :

Modifications not authorized by the manufacturer may void users authority to

operate this device.

az2555/17 20/2/03 16:33 Page 1

1 2 3 4 5 6 ... 11 12