Philips CID3688/00 User Manual download pdf

www.philips.com/welcome

CID3688

www.philips.com/welcome

ENG Quick Start Guide

English

Install the car audio

Connect wires

1 Check the car’s wiring carefully, then

connect them to the two supplied ISO

wires.

Connector Connect to

1CAN BOX

2Red wire The +12V power terminal

which is live in the accessory

(ACC) position of the

ignition switch

If there is no accessory

position, connect to the

+12V car battery terminal

that is always live. Be sure

to connect the black ground

(earth) lead to a metal surface

RIWKHFDUÀUVW

3 Orange

wire

Illumination switch

4Black wire A metal surface of the car

First connect the black

ground (earth) lead, then

connect the yellow and red

power supply leads.

5Yellow wireThe +12V car battery which

is live at all times.

6Blue wire The electric antenna control

lead or power supply lead of

the antenna booster

If there is no electric antenna

or antenna booster, or it is

manually operated telescopic

antenna, it is not necessary to

connect this lead.

7CAN BOX

8 Green and

green/black

wires

Left speaker (Rear)

9 White and

white/black

wires

Left speaker (Front)

10 Gray and

gray/black

wires

Right speaker (Front)

11 Purple and

purple/black

wires

Right speaker (Rear)

2 Connect the other end of the two ISO

connectors to the car audio system.

3 If necessary, do other connections:

Mount in the dashboard

1 If the car does not have an on-board drive

or navigation computer, disconnect the

negative terminal of the car battery.

2 Ensure that the horizontal slant of the car

dashboard opening is between 0 and

20 degrees. The unit cannot be used if

the dashboard opening’s slant angle is

above 20 degrees.

3 Install the mounting bolt and place the

supplied rubber cap over the end of the

mounting bolt.

4 6OLGHWKHXQLWLQWRWKHGDVKERDUGDQGÀ[LW

WRWKHFDUZLWKÀYHVFUHZV

5 Reconnect the negative terminal of the car

battery.

Turn on

Caution

Risk of road accidents! Never watch video or



adjust settings while you drive.

1 Press and hold /MUTE/VOL to turn on

the unit.

The available OSD (On-Screen Display) »

languages are displayed.

2 Tap a language to select.

The OSD language is changed to the »

selected language immediately.

To turn off the unit, press and hold 

/MUTE/

VOL.

Adjust screen

To adjust screen brightness

1 Press DISP/ / to show the brightness bar.

2 Tap / to adjust the value.

3 Press DISP/ / WRFRQÀUP

To turn on/off the screen, press and hold DISP/

/ .

Set date and time

Tap the upper left corner to display the

main menu.

2 Tap in the middle right side of the screen.

The second main menu is displayed.»

3 Tap [Settings].

4 Tap [Time].

The date/time setup menu is displayed. »

Set date

1 Tap [Date].

2 Tap on the displayed date information.

A submenu is displayed.»

3 Tap or to set year, month and day.

Set clock mode

1 Tap [Clock mode].

2 Tap on [12Hr] or [24Hr] to select clock

mode.

Set time

1 Tap [Time].

2 Tap on the displayed time.

A submenu is displayed.»

3 Tap or to set hour and minute.

Use map

Note

You may need to upgrade the map before



using it (see “Upgrade the map” section).

1 Tap the upper left corner to display the

main menu.

2 Tap [Navigation].

The navigation menu is displayed in a »

few seconds.

3 Refer to the map manual (in Chinese) to

operate the navigation tool.

Listen to Radio

Tap to display the home menu.

2 Tap [Radio].

» Band and frequency information is

displayed.

3 Tap on FM or AM to select band:

4 %ULHÁ\WDS or to tune to a radio station

by step.

Play disc

You can play video, audio or images stored on the

following discs:

DVD video, DVD-R, DVD-RW

VCD

Audio CD, CD-R, CD-RW

1 Insert the disc into the disc slot with the

label side facing up.

Play starts automatically. »

To remove the disc, press »

Connect USB device

1 Insert your USB device to the USB socket.

Play starts automatically.»

Remove the USB device

1 Switch to another (non-USB) source.

2 Remove the USB device.

Insert SD/MMC card

1 Open the SD/MMC card cover.

2 Insert the SD/MMC card into the SD/MMC

card slot.

Play starts automatically.»

Remove the SD/MMC card

1 Switch to another source.

2 Press the card until you hear a click sound.

The card is now disengaged.»

3 Remove the SD or MMC card.

Play with Bluetooth device

Pair the Bluetooth-enabled devices

To connect your Bluetooth device to the unit, you

need to pair the device to the unit. Pairing needs

only to be done once.

You can pair up to eight devices.

1 Turn on the Bluetooth function on the

device.

CID3688_00_QSG_V1.0

Yellow Green Blue

Red

Black

Yellow

Blue/white

Pink

een/white

Gearbox

AV system

AUX

Red

White

Yellow

Red

White

Yellow

Rear display

Wireless headphone

Yellow

Black

GPS antenna

Amplifier

White

Red

Brown

Radio antenna

2 Search for Bluetooth device with the

device.

3 Select “CID3688” in the pairing list.

4 Enter default password “0000”.

if pairing succeeds. phone call record is »

displayed.

Make a call

1 Pair the phone with the unit.

2 Tap to display the home menu.

3 Tap [Bluetooth].

The Bluetooth menu is displayed.»

4 Tap or to select the paired phone, then

tap

5 Tap or to search for phone number

from the following list:

Or tap to dial number directly, then tap

to dial.

Receive call

By default, all incoming calls are received

automatically.

1 If there is incoming call, [Incoming call...]

ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH

Bluetooth microphone.

2 When conversation ends, tap (red) to

terminate the call.

Summary of Contents

Page 1 - CID3688_00_QSG_V1.0

www.philips.com/welcomeRegister your product and get support atCID3688www.philips.com/welcomeRegister your product and get support atENG Quick Start G

Comments to this Manuals

No comments

Philips CID3688/00 User Manual

Browse online or download User Manual for Car navigation systems Philips CID3688/00. Philips Car infotainment system CID3688/00 Quick start guide

Summary of Contents

Comments to this Manuals