Philips QG3392/45 User Manual download pdf

Trimming Eyebrows

wUse the detail and eyebrow comb to trim

eyebrows and sideburns.

1 Be certain the Groomer is in the OFF

position.

2 Put the precision trimmer on the Groomer

handle (1) and turn clockwise (2) (fig. 20).

3 Slide the detail and eyebrow comb onto the

precision trimmer (fig. 23).

4 Turn the Groomer ON (fig.5).

5 Move the Groomer slowly against the direc-

tion of hair growth. Press lightly making sure

the surface of the comb is in full contact with

the skin (fig. 24).

Shaving With Mini Foil Shaver

Use the narrow mini shaver to shave along

contoured edges to remove any stubble while

creating a smooth, well-defined beard line.

w Before using the mini shaver, always check it

for wear and damage. If the mini shaver shows

signs of wear or damage, do not use it as injury

may occur. Do not use the mini shaver until it

has been replaced.

1 Pre-trim the contours desired with the

trimmer or precision trimmer without a

comb attachment.

2 Put the mini shaver on the Groomer handle.

3 Gently press the mini shaver onto the skin

and shave along contoured edges to remove

any stubble. Do not press too hard (fig. 22).

Grooming Nose/Ear Hair

1 Be certain the Groomer is in the OFF

position.

2 Remove the trimmer by turning counter-

clockwise and pulling it off the Groomer

handle.

3 Put the nose/ear hair trimmer on the

Groomer handle (1) and turn clockwise (2)

(fig. 25).

Trimming Nose Hair

w Make sure nasal passages are clean.

1 Put the nose/ear hair trimmer on the

Groomer handle (1) and turn clockwise (2)

(fig. 25).

2 Turn the Groomer ON and insert the tip

of the attachment into one nostril (fig. 26).

CAUTION: Do Not insert the tip more

than 3/16 in./5mm into your nostril.

3 Slowly move the tip in and out while

turning it around at the same time in order

to remove unwanted hair. For best results,

make sure the side of the tip is firm against

skin. This will reduce the tickling effect that

can occur during trimming of nose hair.

4 Turn off Groomer. Rinse attachment clean

after each use.

Trimming Ear Hair

w Clean outer area of ear and ear canal. Make

sure it is free of wax.

w Nose/ear hair trimmer should be on the

Groomer.

1 Turn the Groomer ON and move the tip

softly around the edge of ear to remove hairs

extending beyond the outer ear (fig. 27).

2 Carefully insert the tip into outer ear canal

(fig. 28).

CAUTION: Do not insert the tip further

than 3/16 in./5mm into the ear as this

could cause damage to the eardrum.

3 Turn off Groomer. Rinse attachment clean

after each use.

Cleaning

w Clean the attachments after each use.

w Always switch Groomer OFF, unplug

and remove power supply cord from

Groomer before cleaning.

w Do not use compressed air, abrasive cleaning

agents, scourers or liquids such as alcohol,

benzene, bleach or acetone to clean the

Groomer and attachments.

w Never clean, replace or remove Groomer

attachments with motor ON.

w Do not apply pressure to cutters.

w Do not touch cutters with hard objects as this

may damage them.

2 To contour the hairline around the ears,

comb the hair ends over the ears.

3 Tilt the Groomer in such a way that only

one edge of the cutter blades touches the

hair ends when you shape the contours

around the ears (fig. 16).

Be careful not to trim too much. The hairline

should be close to the ear.

4 To contour the nape of the neck or

sideburns, turn the Groomer and make

downward strokes (fig. 17).

5 Move the Groomer slowly and smoothly

following the natural hairline.

Trimming your Beard & Moustache

with Beard & Moustache Comb

1 Put the trimmer on Groomer handle (1) and

turn clockwise (2) (fig. 2).

2 Slide the beard & moustache comb into

the guiding grooves on both sides of the

handle (fig. 18)

3 Press the Hair Length Setting Selector (1)

and slide the comb to the desired setting (2)

(fig. 19).

The beard and moustache comb cuts hair to a

length of 3/64-23/32in / 1-18mm.

w If you are trimming for the first time, start

by using the comb at the maximum trimming

length setting (23/32 in/18mm) to prevent

accidentally trimming hairs too short. As you

become familiar with the settings, adjust Hair

Length Setting Selector to desired trimming

length. Selector will “click” into position at each

setting.

4 Turn the Groomer ON (fig. 5).

5 To trim in the most effective way, move

the Groomer against the direction of hair

growth. Make sure the surface of the comb

always stays in contact with the skin.

NOTE: Since all hairs do not grow in the same

direction, you may want to try different trimming

positions (i.e., upwards, downwards, or across).

Practice is best for optimum results.

wIf a lot of hair has accumulated in the comb,

remove the comb and blow and/or shake the

hair out of the comb.

w REMEMBER: You must reset the hair length

selector back to your desired setting every time

you replace the comb on the appliance.

wThe remaining hair length corresponds with

the smallest distance between the cutting

blade and the spot where the comb is in contact

with the skin.

Beard Trimming Without

Beard & Moustache Comb

Remove comb if you are:

w Defining hair lines

w Trimming nape of neck

w Removing single, unwanted hairs

1 Be certain the Groomer is in the OFF

position.

2 Remove the comb by pressing the Hair

Length Setting Selector (1) and slide the

comb upwards (2). Pull comb off Groomer .

3 Turn the Groomer ON (fig. 5).

4 Make well-controlled movements. Touch the

hair/skin lightly with the Groomer.

Styling/Contouring with Precision

Trimmer

w Use the precision trimmer to cut shapes in

beard hair or scalp hair.

w Be careful when using the precision trimmer as

it removes every hair it touches.

1 Put the precision trimmer on the Groomer

handle (1) and turn clockwise (2) (fig. 20).

2 Make careful and controlled movements with

the precision trimmer.

3 For best results, move the precision trimmer

against the direction of hair growth making

sure it is in full contact with the skin (fig. 21).

TIP: For the perfect finish, use the mini foil shaver

to make edges and lines of your beard style even

smoother (fig. 22).

w Make sure the shaving foil is in complete

contact with your skin for the closest shave

and minimum foil wear.

w Pressing too hard may cause skin irritation.

w Practice is best for optimum results.

1 Put the Bodygroom Shaver on the Groomer

handle (1) and turn clockwise (2) (fig. 7).

2 Turn the Groomer ON (fig. 5).

3 Stretch your skin taut with your free hand

and gently press Groomer to skin and move

it slowly and smoothly, making sure the

shaving foil is in full contact with the skin

(fig. 8). Do not press too hard. Too much

pressure can distort the foil and cause skin

irritation.

TIP: Stretching your skin can help hairs stand upright

and minimize the chance of skin irritation.

4 Always move the Groomer against the

direction of hair growth (fig. 9).

5 Turn OFF Groomer (fig. 5). Clean the

body shaver after each use.

Hair Clipping

wMake sure that the appliance is fully charged

before you start clipping hair.

w Before you start clipping, make sure that the

head of the person whose hair you are cutting

is at the same level as your chest so that all

parts of his/her head are clearly visible and

within easy reach.

w Make sure the hair is clean and dry.

w Before you begin, comb the hair in the direction

of growth (fig. 10).

w To achieve optimal clipping results, always move

the appliance slowly through the hair against

the direction of hair growth.

Clipping with hair clipping comb

1 Put the trimmer on Groomer handle (1) and

turn clockwise (2) (fig. 2).

2 Slide the hair clipping comb into the guiding

grooves on both sides of Groomer handle

(fig. 11).

3 Press the Hair Length Setting Selector (1)

and slide the comb to the desired setting (2)

(fig. 12).

The hair clipping comb cuts hair to a length of

1/8 in - 25/32 in / 3-20mm.

4 The setting selected is shown on the back

of the Groomer.

When you are clipping for the first time, start

at the maximum clipping length setting (25/32

in/20mm) to familiarize yourself with the appliance

and prevent accidentally trimming hairs too

short. As you become familiar with the settings,

adjust the Hair Length Setting Selector to desired

trimming length. Selector will ‘click’ into position at

each setting.

5 Turn the Groomer ON (fig. 5).

6 Make sure that the flat part of the comb is

always in full contact with the scalp to obtain

an even result (fig. 13).

7 Move the appliance slowly over the crown

from different directions to achieve an even

result (fig. 14).

8 Always move the appliance against the

direction of hair growth.

9 Make overlapping passes over the head to

ensure that all hair that should be cut has

been cut.

10 Turn the Groomer off and remove the hair

clipping comb often to blow and/or shake

out hair that has accumulated.

w REMEMBER: You must reset the hair length

selector back to your desired setting every

time you replace the hair clipping comb on the

appliance.

TIP: Write down the settings you have used to create

a certain hairstyle as a reminder for future clipping

sessions.

Contouring without the hair clipping

comb

w Use the Groomer without a comb to clip hair

very close to the skin (3/64in./1mm) or to

contour the neckline and area around the ears.

1 Remove the hair comb by pressing the Hair

Length Setting Selector (1) and slide the

comb upwards (2). Pull comb off Groomer

(fig. 15).

Be careful when you are clipping without a comb

attachment as when the Clipper is turned on it

will remove every hair it touches.

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electric appliance, basic safety

precautions should always be followed,

including the following:

Read all instructions before using this

appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for a corded groomer that

has fallen into water. Unplug immediately.

2. Power plug and the accessories connected

to it are not for immersion or for use in

shower.

3. Do not use an extension cord with this

appliance.

4. Always unplug the groomer from the

electrical outlet immediately after use,

except when groomer is (re)charging.

5. Unplug and remove power supply cord

from groomer before cleaning.

6. The batteries used in this device may

present a fire or chemical burn hazard if

mistreated. Do not disassemble, heat above

100°C (212°F) or incinerate.

WARNING

To reduce the risk of burns, fire, electric

shock or injury to persons:

1. Close supervision is necessary when

this appliance is used by, on, or near chil-

dren or invalids.

2. Use this groomer for its intended house-

hold use as described in this manual. Do

not use attachments not recommended

by Philips Electronics North America

Corporation.

3. Never operate this groomer if it has a

damaged cord or plug, if it is not working

properly, if it has been dropped, damaged,

or dropped into water while plugged in.

For assistance call 1-800-243-3050.

4. Keep the groomer, cord, charging plug and

any attachments away from heated

surfaces.

5. Never drop or insert any object into any

opening.

6. Do not operate, charge, clean or plug

in groomer outdoors or where aerosol

(spray) products are being used or where

oxygen is being administered.

7. Always check foils, cutters, cutting unit,

combs and trimmers before using the

groomer. Do not use the groomer if foils,

cutters, cutting unit, combs or trimmers

are damaged, as injury may occur.

8. Always attach plug to groomer first, then

to outlet. To disconnect, turn groomer

“OFF”, then remove plug from outlet.

9. To prevent possible damage to the cord,

do not wrap cord around the groomer.

10. Never put groomer in direct sunlight or

store at a temperature above 140°F.

11. This groomer is for use on human hair

only. Do not use this groomer for any

other purpose.

12. Groomer is water-safe and can be rinsed

under running tap water or used in the

shower. Do not submerge groomer in

water.

13. Only use the power plug and other

accessories supplied with the appliance.

SAVE THESE

INSTRUCTIONS

IMPORTANT: The power plug contains

a transformer. Do not cut off the power

plug to replace it with another plug as

this will cause a hazardous condition.

6 Disconnect the cord and unplug from

electrical outlet.

Turbo Power

w Simply press the Turbo Button for a turbo

power boost for fast results and the Turbo

indicator will light up blue. The memory

function will remember the last used setting.

Body Trimming

w Use this Groomer for its intended household

use as described in this manual.

w Before using, check foil, cutters and trimmers

for wear or damage. If foil, cutters or trim-

mers show signs of wear or damage, do not

use Groomer as injury may occur. Do not use

Groomer until foil, cutters or trimmers have

been replaced.

w Make sure that the Groomer is fully charged

before you start trimming.

wMake sure hair is clean and dry as wet hair

tends to stick to the body.

Take your time and do not move the Groomer

too fast. Make smooth and gentle movements.

1 Charge according to directions. Unplug

groomer from outlet and remove cord.

2 Press ON/OFF button ON to begin trimming.

3 If the charge runs low, the battery status

indicator will light up orange.

4 Connect appliance plug to Groomer. A quick

charge for 5 minutes gives you 5 minutes of

trimming time.

Body Trimming with Body Trimming

Comb

w Always use the body trimming comb when

trimming sensitive areas.

1 Put the trimmer on the Groomer handle

(1) and turn clockwise (2) (fig. 2).

2 Slide the body trimming comb into the

guiding grooves on both sides of the handle

(fig. 3).

3 Press the Hair Length Setting Selector (1)

and slide the comb to the desired setting (2)

(fig. 4).

The body trimming comb cuts hair to a length of

1/8 - 15/32in / 3-12mm.

4 The setting selected is shown on the back

of the Groomer.

w If you are trimming for the first time, start

by using the comb at the maximum trimming

length setting (15/32 in/12mm) to prevent

accidentally trimming hairs too short. As you

become familiar with the settings, adjust Hair

Length Setting Selector to desired trimming

length. Selector will ‘click’ into position at each

setting.

5 Turn the Groomer ON (fig. 5).

6 To trim in the most effective way, move the

Groomer slowly against the direction of hair

growth (fig. 6). Make sure the surface of the

comb always stays in contact with the skin.

NOTE: Since all hairs do not grow in the same

direction, you may want to try different trimming

positions (i.e., upwards, downwards, or across).

Practice is best for optimum results.

w If a lot of hair has accumulated in the comb,

remove the comb and blow and/or shake the

hair out of the comb.

w REMEMBER: You must reset the hair length

setting selector back to your desired setting

every time you replace the comb on the

appliance.

w The length setting is equal to the hair length

that will remain after trimming.

7 Turn off Groomer (fig. 5). Rinse the comb

clean after each use.

Body Shaving with Bodygroom

Shaver

w Do not use this Groomer to shave facial or

scalp hair. The Groomer should only be used

on skin below the neckline.

w When shaving sensitive areas, you may feel

some discomfort, irritation or reddening of the

skin. This is normal as your skin needs time to

adjust to shaving.

w If your hair is longer than 13/32 in/10 mm,

trim hair with the body trimming comb first

for optimum shaving results.

w For dry use, be certain your skin is clean and

dry before using the Groomer.

w For wet use, you may prepare your skin with

lathered soap or shaving foam before using the

Groomer.

w Do not use the shaver if foil or cutters are

damaged or broken as injury may occur.

During Use:

w If cut hairs have accumulated in the comb area,

remove hairs by shaking or blowing. Remember

to adjust the trimming length back to your

selected setting when you replace the comb

on Groomer.

After Each Use:

1 Make sure the Groomer is switched OFF

and disconnected from the electrical outlet.

2 Remove any comb or attachment.

3 Blow and/or shake out any hair that may

have accumulated in the comb or attachment.

4 Rinse combs, attachments and appliance

under warm tap water.

5 Shake excess water from combs and

attachments and allow to air dry thoroughly.

6 Place the attachment back on the Groomer

handle.

Cleaning the Mini Foil Shaver

1 Separate the top part of the mini shaver

from its body (fig. 29).

2 Blow and/or shake out any hair that may

have accumulated inside the mini shaver

(fig. 30).

3 Clean the top part of the mini shaver under

warm tap water (fig. 31).

w The shaving foil is very delicate and should not

be handled.

w If foil becomes damaged, do not continue

using the mini shaver. Do not apply pressure

to shaving foil.

4 Shake excess water from mini shaver and

allow to air dry thoroughly.

Do not use a towel to dry the mini shaver as

damage to the shaving foil could occur.

Cleaning the Body Shaver

1 Pull the shaving unit out of the body shaver

(fig. 32).

2 Blow and/or shake out any hair that may have

accumulated inside the body shaver (fig. 33).

3 Clean the body shaver and shaving unit

under warm tap water (fig 34).

w The shaving foil is very delicate and should not

be handled.

w If foil becomes damaged, do not continue

using the body shaver. Do not apply pressure

to shaving foil.

4 Shake excess water from body shaver and

shaving unit and allow to air dry thoroughly.

Do not use a towel to dry the shaving unit as

damage could occur.

Replacing the Bodygroom Shaver

Shaving Foil Head

w If the shaving unit is worn or damaged, do not

continue using the Bodygroom shaver. Replace

the shaving unit immediately.

w It is recommended that you replace your

shaving unit once a year.

w A worn or damaged shaving unit should only

be replaced with an original Philips Norelco

shaving foil, model BG2000, which is

available on the Philips Norelco website,

www.philips.com/support or call

1-800-243-3050 for assistance.

w The foil is a precision part. Handle with care.

1 Always switch Groomer OFF and remove

Groomer plug from outlet before

replacing shaving unit.

2 Remove the shaving unit head by pulling it off

the appliance.

3 Place the new shaving unit head on the

Groomer by snapping it into place.

You will hear a “click”.

After replacing the shaving unit head, check that

the shaving head is firmly attached before using

Groomer.

This Groomer has no other user-serviceable

parts. For assistance call 1-800-243-3050.

A Bodygroom Shaver

B Mini Foil Shaver

C Nose/Ear Hair Trimmer

D Precision Trimmer

E Full Size Metal Guard Trimmer

F Handle

G On/Off Button

H Turbo Button

I Turbo Status Indicator

J Battery Status Indicator

K Hair Clipping Comb

L Beard and Moustache Comb

M Body Trimming Comb

N Detail and Eyebrow Comb

O Adapter

P Small Appliance Plug

Pouch (not shown)

Full 2-Year Warranty

45-Day Money-Back Guarantee

This symbol indicates that

the Groomer can be used

in the bath or shower.

Registration

Congratulations on your purchase and welcome

to Philips Norelco!

To fully benefit from the support that Philips

Norelco offers, register your product at

www.norelco.com/register

Put It To The Test

Like many new products, your Philips Norelco

Multigroom may take a little getting used to. If

you are using an electric Groomer for the first

time, or if you’ve been using a different brand,

take the time to acquaint yourself with your new

Grooming Kit.

Your Multigroom features head to toe styling

with a Bodygroom shaver and powerful battery

combined with all the attachments to make

trimming facial hairs or hair clipping goof proof.

Throw your scissors away and put your new

Multigroom to the test. We guarantee precise,

professional results or Philips Norelco will refund

you the full purchase price as long as the request

is received within 45 days of purchase.

3-12mm

1-18mm

3-20mm

3 - 20

Storage

w Be sure Groomer is turned OFF. Remove cord

from outlet and Groomer before storing in a

safe, dry location where it will not be crushed,

banged, or subject to damage.

w Store the Groomer and attachments in the

pouch to prevent damage.

w Do not wrap cord around Groomer when

storing.

w Store cord in a safe location where it will not

be cut or damaged.

w Do not place or store Groomer where it can

fall or be pulled into a tub or sink, water or

other liquid while plugged in.

Assistance

For assistance visit our website:

www.philips.com/support

or call toll free: 1-800-243-3050

Online information is available 24 hours a day,

7 days a week.

Battery Recycling

w This Philips Norelco Groomer contains a

rechargeable Lithium-Ion battery, which must

be disposed of properly (fig. 35).

w Contact your local town or city officials for

battery disposal information or call

1-800-8-BATTERY or www.rbrc.com for

drop-off locations.

w For assistance, visit our website:

www.philips.com/support or

call toll free: 1-800-243-3050.

Features

ENGLISH

To Charge/Recharge

w Fully charge Groomer before using for the first

time or after non-use for a long period of time.

w Charging, recharging or using Groomer at

 temperaturesbelow40˚Forhigherthan95˚F

adversely affects lifespan of the battery.

w If the Groomer is subjected to a major change

in temperature, pressure or humidity, let the

Groomer acclimatize for 30 minutes before

using.

1 Be certain Groomer is OFF.

2 Connect small plug to Groomer and plug the

adapter into any 120V AC outlet (fig. 1). Use

only the cord provided.

w An adaptor plug may be necessary for power

cord usage in some foreign countries. Use an

attachment plug adaptor of the proper

configuration for the power outlet.

3 It will take approximately 1 hour to fully

charge the Groomer for a cordless trimming

time of up to 60 minutes.

4 The Battery Status Indicator will blink white

to indicate the Groomer is charging.

5 If the battery runs low (approximately 10

minutes of grooming time left) the Battery

Status Indicator will light up orange indicat-

ing the Groomer needs to be (re) charged.

4222 002 8561 1

45-DAY MONEY-

BACK GUARANTEE

If you are not fully satisfied with your Philips Norelco

Groomer send the product back and we’ll refund you

the full purchase price.

The Groomer must be shipped prepaid by

insured mail, insurance prepaid, have the original

sales receipt, indicating purchase price and date

of purchase, and the money-back guarantee

return authorization form enclosed. We cannot

be responsible for lost mail.

The Groomer must be postmarked no later

than 45 days after the date of purchase. Philips

Norelco reserves the right to verify the purchase

price of the product and limit refunds not to

exceed suggested retail price.

To obtain money-back guarantee return

authorization form, call 1-800-243-3050 for

assistance.

Delivery of refund check will occur 6–8 weeks AFTER

receipt of returned product.

Full Two-Year Warranty

Philips Electronics North America Corporation warrants each new Philips

Norelco product, Model QG3392 (except cutters, combs and foils)

against defects in materials or workmanship for a period of two years

from the date of purchase, and agrees to repair or replace any defective

product without charge.

IMPORTANT: This warranty does not cover damage resulting from

accident, misuse or abuse, lack of reasonable care, the affixing of any

attachment not provided with the product or loss of parts or subjecting

the product to any but the specific voltage.* Use of unauthorized

replacement parts will void this warranty.

PHILIPS ELECTRONICS NORTH AMERICA CORPORATION

WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY

A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT

REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM

WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED

REPAIR SERVICE. NO RESPONSIBILITY IS ASSUMED FOR ANY

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply go to www.philips.com/

norelco or call 1-800-243-3050 for assistance. It is suggested that for

your protection you return shipments of product by insured mail,

insurance prepaid. Damage occurring during shipment is not covered by

this warranty. NOTE: No other warranty, written or oral, is authorized

by Philips Electronics North America Corporation. This warranty gives

you specific legal rights, and you may also have other rights which vary

from state to state. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above exclusion and

limitations may not apply to you.

*Read enclosed instructions carefully.

Manufactured for:

Philips Consumer Lifestyle

A Division of Philips Electronics North America Corporation

P.O. Box 10313, Stamford, CT 06904

This symbol on the product’s nameplate means it is

listed by Underwriters’ Laboratories, Inc.

Norelco is a Registered Trademark of Philips Electronics

North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke Philips N.V.

QG3392

Rechargeable Cordless

Electric Groomer

Always here to help you

Question?

Contact

Philips

Norelco

Question?

Contact

Philips

Norelco

www.norelco.com/register

GROOMGROOMMULTIGROOM 75007500

SERIES 7000SERIES 7000

14_QG3392.indd 1 11/19/14 10:18 AM

1 2

Summary of Contents

Page 1 - BACK GUARANTEE

Trimming EyebrowswUse the detail and eyebrow comb to trim eyebrows and sideburns. 1 Be certain the Groomer is in the OFF position. 2 Put

Page 2 - DINERO DE 45 DÍAS

1/8 - 15/32 in3-12mm3/64 - 23/32 in 1-18mm1/8 - 25/32 in3-20mmABCKLMNOPDEFGHIJ 3 Encienda la afeitadora en la posición ON (figura 5). 4 Realice

Comments to this Manuals

No comments

Philips QG3392/45 User Manual

Browse online or download User Manual for Beard trimmers Philips QG3392/45. Philips Multigroom 7500 Grooming kit, Series 7000 QG3392/45 User manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Beard trimmers Philips QG3392/45